Availability of a Replacement Trailer Wiring Connector for a 2003 Toyota Tundra with Tow Package

Question

Question:

I have 2003 toyota tundra that has a towing package ,but I need to replace the receptical and harness. Do you have a direct or OEM replace for that?

asked by: Norm J

0

Expert Reply:

The Tow Ready Wiring Harness, # 20137, will connect to the factory connectors on the 2003 Toyota Tundra, but the receptacle does not fit in the factory location. This is the only replacement harness that we offer for the 2003 Toyota Tundra. I have included a link to the installation details for you.

expert reply by: Michael H

0

Answer 1

Hi Jeff, welcome back and sorry to hear that gave you so much trouble. The Redarc Tow-Pro Link Bluetooth Brake Controller #RED57AR will work on your Silverado. This plugs in-line at the back of your 7-way at the rear of the truck. You can either…

view full answer...

Answer 2

The biggest difference will be price. The two harnesses are basically the same harness made by two different companies. The Curt part #C55382 would be what I would go with over the Hopkins #42475 because the price is better and because we seem to…

view full answer...

Answer 3

Since the Hopkins 7 and 4-Way trailer connector #HM40975-11998 includes a hardwire harness it technically could be installed on any vehicle, including your 2002 Toyota Tundra with a 4-Way connector. But you will need to do some hardwiring and extra…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Availability of a Replacement Trailer Wiring Connector for a 2003 Toyota Tundra with Tow Package

Continue Researching