Rear Replacement Support for Yakima Skybox 21

Question

Question:

I have the Yakima Skybox 21 and the rear support is bent. The one I have looks different than this single arm as is has two arms.

asked by: Doug

0

Expert Reply:

I contacted Yakima and the rear support you need for the Yakima Skybox 21 part # Y07337 is part # 8880683. The older version of the Skybox 21 did use the two arm rear support but you can replace the older two arm version with the updated single arm support.

expert reply by: Heather A

0

Answer 1

So even though your Yakima SkyBox 18 #Y07336 or SkyBox21 #Y07337 has the diamond shaped hinges currently, those are an older model hinge that is no longer used by Yakima; you also won't be able to use the Replacement Front Lid Support 8870090…

view full answer...

Answer 2

I spoke with Yakima, and they said that the Replacement Lid Support for Yakima Cargo Boxes #8880684 and the Replacement Lid Support for Yakima Cargo Boxes #8880683 are the essentially the same thing minus the spring color, oddly enough. But, even…

view full answer...

Answer 3

I spoke with Yakima, and they said the correct replacement for both the front and back of your Yakima SkyBox Pro 16S is the Replacement Lid Support for Yakima Cargo Boxes #8880683. So since you need one for the front and the back, you'd just need…

view full answer...

Answer 4

I checked with Yakima and for your Skybox 16 the correct lid support for the rear is supposed to be part #8870072 and for the front is part #8870090. The picture you submitted shows a broken or twisted part #8870090 so that is what you'd need as…

view full answer...

Answer 5

The first thing that comes to mind is that maybe your front support arm is a little loose or worn. I reached out to my contact at Yakima who said that sometimes they can warp or get twisted which could then result in the lid being a little loose. If…

view full answer...

Answer 6

I checked with Yakima and for the SkyBox 21 the correct lid supports are part #8880683 and #8880684.

view full answer...

Answer 7

I checked with Yakima and for the SkyBox 21 made from 2009 to present the lift struts are part #8880683 for the rear and #8880684 for the front.

view full answer...

Answer 8

The Yakima Skybox 21 part #Y07337 made from 2014 to present has a much more aerodynamic shaped lid than the Yakima Skybox 21 part Y07184 made from 2009 to 2014 had. I have attached a photo of each so you can see the difference. If you have the 09-14…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Rear Replacement Support for Yakima Skybox 21

Products Featured in This Question

Continue Researching