Red Version of LED Clearance and Side Marker Light w/ Turn and Reflector

Question

Question:

Can get one with red lenses

asked by: William C

0

Expert Reply:

You'd have to remove the lens of the part # MCL32ATB and install the lens part # A32RB as there isn't a red version of the light.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 11

Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…

view full answer...

Answer 12

Hey Greg, welcome back! So this is a great question but for a Dexter 3,500-lb axle, the castle/spindle nut does not stay torqued to a specific ft-lb value. Dexter's official bearing-adjustment procedure is while rotating the hub, tighten the…

view full answer...

Red Version of LED Clearance and Side Marker Light w/ Turn and Reflector

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching