How To Install the ThinLine LED Light As An Identification Light On Trailer Over 80 Wide
Updated 02/18/2019 | Published 02/16/2019 >
Products Featured in This Question
Question:
The tear I am building is a little over 80inch wide requiring an identification light so I am using the Optronics ThinLine LED Trailer Tail Light - Stop, Tail, Turn I purchased from etrailer. I have a 6 wire harness I also purchased from etrailer and would like to know how to connect the wires to the identification light at the rear center of the trailer. Harness wires are: White ground - 1 wire Brown split to each side for tail/running lights - 2 wires Green right brake/turn signal - 1 wire Yellow left brake/turn signal - 1 wire Identification has 3 wires - white, black, and red Thanks for your help
asked by: Edwin
Expert Reply:
The ThinLine LED Trailer Tail Light part # STL64RCB when used as an identification light at the top of a trailer over 80" wide will only need to serve one function which is to act as a marker/clearance light. Therefore, there will only be two wires used on the light. The white wire is for ground and will need to be attached to the white ground wire on your trailer and the black wire is for the running light and will need to be attached to the brown wire on either side of your trailer. The red wire can then be tapped off.
In order to mount the light on your trailer I also recommend using the Chrome Mounting Bezel part # A64CRB for a clean look. I have also attached a trailer lighting requirement document for you as well.
Product Page this Question was Asked From
ThinLine LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 15 Diodes - Clear Lens
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- Strip Light
- Surface Mount
- Submersible Lights
- LED Light
- 20-1/2L x 1W Inch
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: rv exterior lights
- Shop: Replacement Fabric for etrailer Powered RV Awning - 18' Wide - 4-Layer Vinyl - Black Fade
- Shop: Optronics Thinline LED Utility Light Bar - Submersible - 11 Diodes - Clear Lens - 15" Long
- Shop: Halogen Docking Light Kit - 35 Watt - Lighted Switch and Safety-Fused Wiring - Black Housing
- Shop: Trailer Wiring
- Search Results: trailer lights
- Search Results: stl64rcb
- Video: The Low-Down on the Chrome Mounting Bezel for Optronics ThinLine Combination LED Tail Light
- Video: Ultimate Overview of the Thinline LED Trailer Tail Light
- Search Results: side marker trailer lights
- Search Results: 5 way flat connector
- Search Results: 5 way wiring harness
- Search Results: submersible lights trailer lights
- Shop: X LED Truck and Trailer Tail Light w/ Reverse Function - Submersible - Oval - Red and White
- Shop: Optronics LED Backup Light for Truck or Trailer - Submersible - 6 Diodes - Oval - Clear Lens
- Shop: GloLight LED Backup Light for Truck or Trailer - Submersible - 22 Diodes - Clear Lens
- Shop: Optronics LED Backup Light for Truck or Trailer - Submersible - 16 Diodes - Clear Lens
- Video: TecNiq LED Trailer Clearance or Side Marker Light DIY Installation - Utility trailer
- Video: Miro-Flex Thinline LED Trailer Clearance or Side Marker Light Feature Review
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector



