Hub length of CE Smith Trailer 13110 and 13100

Question

Question:

Can you please tell me what the over all Hub length of CE Smith Trailer 13110 and 13100 is. Is it 4-1/8 inch 4.125?

asked by: Eric T

1

Helpful Expert Reply:

I went out to the warehouse and found that the CE Smith Trailer Hub Assembly # CE13100 measured about 4-1/4" but that was with the plastic still wrapped around it. If you took the plastic away it would probably measure closed to 4-1/8".

The assembly # CE13110 that you referenced is the same exact hub with the only difference being that it uses wheels studs and the part # CE13100 uses wheel bolts.

expert reply by: Jon G

1

Answer 1

The Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased #AKIHUB-440-2-1K won't fit your trailer spindle as it will be too long. The reason is, this hub is designed to work on BT8 spindles, which are longer than…

view full answer...

Answer 2

If the outer diameter of your Bearing Buddy measures 2.125" then you need the Model 19B Replacement Bearing Buddy Bras #BB19B. These are compatible with models that have an outer diameter of 2-1/8" (or 2.125" in decimal form). Attached…

view full answer...

Answer 3

Based on the dimensions that you listed your trailer has the BT8 spindle on it. That would mean that the hub part #CE13100 that you referenced would fit it and work well.

view full answer...

Answer 4

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 5

The #AKIHUB-545-2-G-2K uses #L44649 bearings with an inner diameter of 1.063" and also has a 5 on 4-1/2 bolt pattern. Since you need #L44643 bearings with an ID of 1" and a 4 on 4 bolt pattern the correct part would be the Trailer Idler Hub…

view full answer...

Answer 6

We do have hubs available for a 1" straight spindle in part #AKIHUB-440-2-EZ-1K. This hub measures 4-1/4" deep so it will run a bit longer than the hub you are looking for. There are a total of 4 hubs that we carry for a 1" straight…

view full answer...

Answer 7

The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that will list the weight capacity. You can…

view full answer...

Answer 8

Assuming you have a 3,500 lb axle and it uses the most common bearing size you will be able to use the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle #BK2-100. I recommend measuring the spindle where the bearings and…

view full answer...

Answer 9

It sounds like you are needing the CE Smith Trailer Hub Assembly #CE13100. This hub fits on a 1" spindle and has the same 4 bolt lug pattern with the threaded bolts that screw into the hub. The grease seal used has the same 1.249" inner…

view full answer...

Answer 10

Assuming you have a #L44643 inner and outer bearing, the correct bearing kit is the #BK1-100. The hub will depend on the bolt pattern you need. These hubs will come pre-greased and include the bearings, races, and grease seals. For a 4 on 4 I…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Hub length of CE Smith Trailer 13110 and 13100

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching