Replacement Hub Recommendation for Trailer with .99 inch Bearing ID Surface Dimension
Published 10/01/2015
Question:
Looks to be pretty close to what I have, can you please confirm. My hubs and bearings on the trailer I just bought where badly corroded so I was unable to find / read any numbers off of what I have. I have the measurements listed below, any help would be greatly appreciated. OD of both races are 1.980 Inner diameter of both bearings are 0.995 Bearing section on the spindle measured 1.00 The seal section of the spindle is 1.240 OD of the seal measured at the back of the hub was 1.973
asked by: Mike
Expert Reply:
Based on the dimensions that you listed your trailer has the BT8 spindle on it. That would mean that the hub part # CE13100 that you referenced would fit it and work well.
Product Page this Question was Asked From
CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Trailer Hubs and Drums
- Idler Hub
- Pre-Greased
- Standard
- L44643 / L44643
- Standard Grade
- For 2500 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- CE Smith
more information >
Continue Researching
- Search Results: spindle washer
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Video: Review of etrailer Trailer Hubs and Drums - Pregreased Idler Hub - AKIHUB-440-2-1K
- Shop: BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter
- Q&A: Spindle Compatible With Trailer Idler Hub Assembly AKIHUB-440-2-1K
- Q&A: Replacement Idler Hub For 1964 Holsclaw Boat Trailer With 1" Diameter Spindle
- Shop: CE Smith Spindle Nuts, Washers, and Cotter Pins for 1" Axle - Qty 2
- Shop: Square BT8 Spindle for 2,000-lb Trailer Axles - 1-1/2" Wide
- Shop: CE Smith Spindle Axle - Weld on - 1-1/16" Diameter
- Video: Feature Review CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Video: Review of Kenda Trailer Tires and Wheels - Tire with Wheel - KE44WV
- Search Results: bearing buddy caps
- Search Results: hub seals
- Search Results: trailer tires and wheels
- Search Results: bearing buddy
- Q&A: Looking For Replacement Hub For 1969 Boat Trailer
- Q&A: Replacing Hubs and Wheels on 1964 Alpine Sprite Camper Trailer
- Q&A: Recommended Idler Hub Assembly for 1-1/16 Inch Diameter Spindle With Seal 1-1/4 Inches at Spindle
- Search Results: trailer hubs and drums
- Article: Most Popular Wheel Bearings
- Search Results: castle nut
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
on Trailer Hubs and Drums
