What is the Difference Between Trailer Wheel Lug Nut # 12CLN and # 12CLN-L

Question

Question:

I have a 10ft enclosed snowmobile triton trailer and I wanted to get these lugs. what is the difference between the 12cln and the 12cln-l bulge style? Which ones do I need?

asked by: Gerard

0

Expert Reply:

The only difference between the 1/2 Inch Lug Nut, # 12CLN and # 12CLN-L is the length of each. Both are bulge style which means they have a 60 degree tapered end. The inside depth of 12CLN is 1-1/4 inches. The inside depth of 12CLN-L is 1-3/4 inches.

expert reply by: Michael H

0

Ryan H.

12/19/2012

What is the hex size for the nuts?

Patrick B.

12/19/2012

Both the 12CLN and 12CLN-L are 3/4 hex bolt sizes.

Answer 1

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 2

Hey Kevin, we have solid stainless steel lug nuts available with the part #KALN1375S which fit the standard 1/2 inch diameter wheel studs. Have you had issues with lug nuts swelling up and being hard to get off?

view full answer...

Answer 3

The Kenda 5.70-8 Bias Trailer Tire with 8" White Wheel #AM30140 fits 1/2"-20 wheel bolts so you will need a 1/2" lug nut such as the CE Smith #CE11051, though the Offset Spare Tire Carrier #CE27310G.

view full answer...

Answer 4

The R and the D in a trailer tire size stand for radial and bias-ply. A radial tire flexes more than a bias tire, giving it better ground contact, traction, stability, and tread wear. A radial tire will normally run cooler than a bias ply tire,…

view full answer...

Answer 5

The best way to determine which hub assembly you will need is by the bearing numbers and the bolt pattern. Your 2019 Sea Doo Trailer should have a 5 on 4-1/2 Inch bolt pattern. The item you selected, Trailer Idler Hub Assembly for 2,000-lb Axles - 5…

view full answer...

Answer 6

Yes, the CE Smith Trailer Wheel Lug Nut #CE11051 that you referenced is a 1/2 inch x 20 lug nut that uses the same standard cone angle of 60 degrees which vehicles use as well.

view full answer...

Answer 7

Thank you for the picture! The problem you are running into has more to do with the lug nuts you are using than the tire wrenches like part #PTW1 that you referenced. Since the Kenda Karrier S-Trail #AM31215 is a little more recessed where the lug…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What is the Difference Between Trailer Wheel Lug Nut # 12CLN and # 12CLN-L

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching