Availability of Wiring Diagram for the Replacement Power Switch # EJ-3520-PSW

Question

Question:

Would you have a wiring diagram please.

asked by: Robert P

0

Expert Reply:

I am attaching a picture of the Replacement Power Switch # EJ-3520-PSW when it is properly installed on the Electric Jack w/ Footplate # EJ-3520-BBX but unfortunately there isn't a wiring diagram available. If you be mindful to note which position each wire is supposed to be in when you disconnect your current switch you simply just have to install this switch in the same way.

expert reply by: Jon G

0

click to enlarge

Daryl W.

9/5/2020

your picture is showing 4 wires on one side 2 on the other should be 3 to a side do you have a better pic

Jon G.

9/8/2020

We don't have a better pic. Why would the light switch need another function other than power and ground?

Answer 1

I have attached a photo for you that shows how a 7-way trailer connector is wired. If you take a look at the trailer side trailer connector you will see a terminal labeled "12V Power". If you were to run a wire part #10-1-1 (per foot) from…

view full answer...

Answer 2

RAM jacks provided the attached photo showing how the various single and doubled wires connect to the pins on the back of the power switch #EJ-3520-PSW. They do not offer a separate wiring diagram.

view full answer...

Answer 3

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 4

Hey Wayne, the first thing I would check is the condition of the battery that powers the jack as well as the wiring connections made to it. Lifting a jack is a lot harder than lowering so if there is an issue with the power or wiring it will show up…

view full answer...

Answer 5

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 6

Hey Mark, the height of the etrailer Electric Trailer Jack #e23ZV that you referenced above the mounting plate is 20 inches. This is about the shortest dimension you'll get from a jack like this. Would that be enough clearance?

view full answer...

Answer 7

Hey Chris! The black wire on the etrailer Electric Trailer Jack #e23ZV is just a ground wire. Realistically you can ground it however you want but I would say running it to the frame with a self-tapping screw as indicated in the instructions is the…

view full answer...

Answer 8

Hey Michael! The etrailer Electric Trailer Jack w/ 7-Way #e74GV you were looking at will definitely have enough lift for your Coleman 13R. This is a great option if you just want to power the jack off the 7-way on your vehicle instead of running it…

view full answer...

Answer 9

Hey Mike! The etrailer Electric Trailer Jack #e55ZV would be a great replacement for the jack on your 2021 Jayco Jay Flight 242BHS. This has the same lift as your existing jack but with a higher 5,000 lb capacity making it a nice upgrade. It also…

view full answer...

Answer 10

I recommend replacing your jack with our Electric Jack #EJ-3520-BBX. This is a simple jack without the bells and whistles like you are looking for. You get a light, electric jack and manual override should the electric motor die. The jack will bolt…

view full answer...

Answer 11

Electric tongue jacks like the Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black #EJ-3520-BBX are designed to use a 12v power so if you want constant power I recommend using a trailer battery for connection. If you only want…

view full answer...

Availability of Wiring Diagram for the Replacement Power Switch # EJ-3520-PSW

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching