Installation of Replacement Electric Jack Power Switch EJ-3520-PSW

Question

Question:

When I connect the wires to connector for jack does it matter which side I install the connector

asked by: Tom B

0

Expert Reply:

RAM jacks provided the attached photo showing how the various single and doubled wires connect to the pins on the back of the power switch # EJ-3520-PSW. They do not offer a separate wiring diagram.

expert reply by: Adam R

0

click to enlarge

Daryl W.

9/5/2020

Your picture doesn't help I can only see 5 wires and where they hook up can't tell

Jon G.

9/8/2020

This is literally the only photo we have available showing this. If you haven't taken your jack apart yet then I'd take a picture of how it's currently wired so you have something to reference.

Jon G.

9/8/2020

This is literally the only photo we have available showing this. If you haven't taken your jack apart yet then I'd take a picture of how it's currently wired so you have something to reference.

Answer 1

I am attaching a picture of the Replacement Power Switch #EJ-3520-PSW when it is properly installed on the Electric Jack w/ Footplate #EJ-3520-BBX but unfortunately there isn't a wiring diagram available. If you be mindful to note which position…

view full answer...

Answer 2

Hey Wayne, the first thing I would check is the condition of the battery that powers the jack as well as the wiring connections made to it. Lifting a jack is a lot harder than lowering so if there is an issue with the power or wiring it will show up…

view full answer...

Answer 3

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 4

To replace the Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD you'll just need to keep track of how the original was hooked up and replicate that. Unfortunately Lippert doesn't have a wiring diagram but we do have a photo we…

view full answer...

Answer 5

To replace a switch on your RAM 3,500 lb jack you just need the Replacement Power Switch #EJ-3520-PSW, but this also could be a bad internal screw. To determine if it's the switch or the screw you just need to remove the plug on top of the jack…

view full answer...

Answer 6

If you can reply to this email with the pictures I can help you out. Just be sure to let me know what the product is they are installed on!

view full answer...

Answer 7

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 8

Hey Howard, It is possible that the switch is to blame so I would remove the top head cover to take a closer look inside the jack #EJ-3520-BBX. You might just have a loose spade terminal on the back of the switch that needs to be pushed on more. I…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Installation of Replacement Electric Jack Power Switch EJ-3520-PSW

Product Page this Question was Asked From

Continue Researching