Where are the Bearings for the eTrailer Trailer Hubs Made

Question

Question:

Do you know who makes the bearings and seals national, timken etc. in the kit or where the manufacturing origin is?

asked by: Seth

0

Expert Reply:

The bearings and grease seals that are included with the Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K are manufactured by Axle Teknology LLC.

expert reply by: Conner L

0

Answer 1

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 2

Hey Rob; thanks for the photos and it was actually the one with the hub number that did it. That's a BD 545 which is an AxleTek 3,500 lb hub and drum like the Trailer Hub and Drum Assembly #AKHD-545-35-K. The 35 on the axle sticker was a good…

view full answer...

Answer 3

I would go with the LubriMatic LMX Industrial Strength Grease #L11390. This is heavy-duty, premium grease for the toughest lubricating jobs on the biggest, heaviest equipment. It performs better under higher pressures and temperatures than standard…

view full answer...

Answer 4

We have exactly what you need for a pre-greased hub and drum for your Lippert 3,500 lb axle. The correct part number is the following: - Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased #AKHD-545-35-EZ-K…

view full answer...

Answer 5

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 6

That is a great question! The pre-greased hubs like the Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased #AKHD-545-35-EZ-K you were looking at are packed with lithium complex based wheel bearing…

view full answer...

Answer 7

If you have a 3500 lb axle, you'll have a 5 on 4-1/2 inch bolt pattern. You can confirm this by measuring the center to center distance between 2 adjacent wheel studs. If it's 2-5/8 of an inch, you absolutely for certain have a 5 on 4-1/2…

view full answer...

Answer 8

Hey Brian, yes the grease seal of the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K is designed to prevent grease from getting on the brake components. But what I would guess happened to you is that you overfilled the hub…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Where are the Bearings for the eTrailer Trailer Hubs Made

Product Page this Question was Asked From

Continue Researching