What is the Length of the Trailer Idler Hub Assembly # TA88545-2
Published 08/16/2018
Products Featured in This Question
Question:
I have a trinton lite snowmobile trailer with a 1 1/16 inch spindle/shaft diameter. What is the length/height of this hub? The seals are the correct size. What grease do you recommend for this hub assembly? Will this hub fit? THANKS!
asked by: Steven M
Expert Reply:
I went out to the warehouse and found that the total length of the Trailer Idler Hub Assembly # TA88545-2 is 4-1/4". If you have a straight spindle with a diameter of 1-1/16" then the 2 # L44649 bearings should fit just fine, just note that the grease seal has an inner diameter of 1.50" so you will need to make sure that corresponds to what you have. If all of that checks out then this hub will fit!
Always use the same grease that you used the last time that everything was greased. Different greases can actually counteract each other and will cause the grease to harden or become more like liquid so it is always best to use the same grease. If you are not sure what was last used then you can clean off the spindle so that no grease is left on it and then use the LubriMatic Wheel Bearing Grease # L11465. The LubriMatic Deluxe Bearing Packer # L70025 can be used to help speed up the process.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Qty 2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Standard Grade
- For 2500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Trailer Idler Hub Assembly for 2,500-lb Axles: The Breakdown
- Q&A: Replacement Hub and Spindle for 2014 Ranger Trailer
- Search Results: trailer hubs and drums
- Shop: Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Qty 2
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Axle with Idler Hubs - 4" Drop - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Q&A: Correct Replacement Idler Hub for Triton 2 Place Snowmobile Trailer
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 10" to 12"- 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: Gooseneck Hitch
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Search Results: spare tire mount
on Trailer Hubs and Drums
