Will Dexter E-Z Lube Trailer Hub Assembly Work on Non E-Z Lube Spindle
Updated 07/02/2018 | Published 06/28/2018
Products Featured in This Question
Question:
Will this still work on my trailer if I dont have ez lube axles but the same spindle diameters?
asked by: Josh T
Expert Reply:
As long as the spindles on your trailer use the # 25580 inner bearing and the # 14125A outer bearing, the Dexter Trailer Hub and Drum Assembly # 42866UC3-EZ will work perfectly whether or not you have E-Z Lube spindles. The only difference between this EZ Lube hub and a non E-Z Lube hub is that this hub will have a removable rubber seal on the cap that allows easy access to a grease fitting that would be on E-Z Lube Spindles. You can absolutely use this on your standard spindles, though.
This Dexter Hub is designed for 5,200 to 7,500 pound axles and has an 8 on 6-1/2 inch bolt pattern. The bearings, races, and seal are included. I have attached a short video demonstration on this assembly that you can also check out.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly - 7K E-Z Lube Axle - 8 on 6-1/2 - Pre-Greased - 1/2" Stud
- Trailer Hubs and Drums
- Hub with Drum
- EZ Lube
- Pre-Greased
- 25580 / 14125A
- Standard Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer wiring
- Search Results: trailer breakaway kit
- Search Results: 7 way cord
- Search Results: 7 pin to 7 pin extension
- Search Results: 7 pin wiring harness
- Search Results: trailer lights
- Search Results: trailer wiring accessories and parts
- Q&A: What Wire Gauge Does The Curt Cold Weather 7-Way RV Style Connector # C23RJ Use?
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly - 7K E-Z Lube Axle - 8 on 6-1/2 - Pre-Greased - 1/2" Stud
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable - Trailer End - 10' Long
- Shop: Mighty Cord 7-Way RV-Style Trailer Connector w/ Molded Cable - Trailer End - 6' Long
- Shop: Dexter Trailer Hub and Drum Assembly - 5,200-lb to 7,000-lb Axles - 12" Diameter - 8 on 6-1/2
- Video: Trailer Hub and Drum Assembly Spec Review
- Shop: Trailer Wiring
- Q&A: How Do The Breakaway Switch And Electric Brakes Connect To A Trailer's 7 Way
- Q&A: Torque Spec for Tightening Trailer Brake Assemblies to Trailer Spindle
- Q&A: What is Proper Way to Torque Trailer Axle Spindle Nut
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
on Trailer Hubs and Drums
