Solution for Replacing Atwood Surge Actuator

Question

Question:

Hello. I am looking for a replacement kit for atwood 85852 master cylinder. I have the actual master cylinder. I need all the components to go along with it. Thank you.

asked by: Mike

0

Expert Reply:

I wish we had replacement master cylinders for the Atwood actuators but we aren't able to get them anymore so we don't have solutions beyond replacing the entire coupler like with the Demco coupler part # DM72VR which is for drum brakes and has a 7,000 lb capacity.

expert reply by: Jameson C

0

Answer 1

I do have an option for you but the coupler on your trailer is very old and we simply don't carry parts for them anymore as they were discontinued by the manufacturer. Therefore, the only option we can offer is a new coupler, the Demco Hydraulic…

view full answer...

Answer 2

Your best route is to replace your entire surge brake assembly as Atwood no longer produces any parts for their brake actuators. The Titan Zinc-Plated Brake Actuator #T47457207K is going to be your best replacement available. It is specific to disc…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Solution for Replacing Atwood Surge Actuator

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching