How to Replace Trailer Lights with the ONE LED Trailer Tail Light

Question

Question:

Hello, I want to purchase new tail lights for my trailer. Looking at product STL008RB. What is the product code for driver side light. Thank you.

asked by: Jon

0

Expert Reply:

In order to receive a pair of the ONE LED Trailer Tail Lights you would want to use part # STL008RB for the passenger and part # STL009RB for the driver side. I also recommend using butt connectors for installation which can be found using part # DW05744-5.

I have attached a review/install video on these lights for you as well.

expert reply by: Conner L

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hi Ken! It looks like you have almost everything you need to set up your 2026 Jeep Gladiator Sahara for flat towing. The etrailer Invisible Base Plate Kit - Removable Arms #e98948 is a perfect fit and the etrailer XHD Non-Binding Tow Bar - RV Mount -…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 6

The Bulldog Gooseneck Coupler Head Repair Kit #BD1542S01 is specifically for the #BDGN240200 coupler head. This is the Bulldog GN24 which is the same as the Fulton GN24.

view full answer...

Answer 7

Hey Eddie, the Curt hitch part #C22RJ and the Trailermate part #TMT29FR are both very similar in design and capacity. I really like the Curt hitches and recommend them whenever available but Trailer Mate isn't bad either. If you are wanting the…

view full answer...

Answer 8

While we cannot confirm for sure what the "L" means on the 11033L, the "L" does not make a differences when coming to fitment of the hub. With that being said, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern…

view full answer...

Answer 9

Hey Chuck, we have wheel/tire combos that will work for you but it will be based on the bolt pattern of your wheels. Most likely you have a 5 on 4-1/2 inch bolt pattern and the part #AM31994 would work great but if you have a 4 on 4 inch bolt pattern…

view full answer...

Answer 10

The Kenda 205/65-10 Bias Trailer Tire with 10 inch Galvanized Wheel #AM3H400 that you referenced has a tire size of 205/65-10 that is the same as the 205x8-10 that you currently have. If you want just the tire, I would recommend you get a Loadstar…

view full answer...

Answer 11

You will need to cut that off of your 2001 Cobalt 240 to replace the actuator since there are no replacements that will fit. I recommend welding on a straight tongue so you can use a bolt-on actuator like the Dexter Zinc-Plated Brake Actuator…

view full answer...

Answer 12

You can certainly adapt a 7-way trailer connector on a trailer to a 4-pole on a vehicle by installing the #37185 adapter you referenced. Simply use the included mounting bracket to install the adapter onto the vehicle, and plug the 4-pole portion of…

view full answer...

How to Replace Trailer Lights with the ONE LED Trailer Tail Light

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching