Recommendations for installing a LED Trailer Light # STL35RB on a 2002 Ranger Trail Trailer

Question

Question:

What do I need to replace original sealed bulb trailer light with # STL35RB LED lights? Will it work and how and what do I need to do it? I am sure this is not the first time but it has been hard to find this info. 2002 ranger trail trailer. thanks

asked by: C. H

0

Expert Reply:

This Miro-Flex, Waterproof, Rectangular, LED Trailer Stop/Turn/Tail Light # STL35RB that you referenced should work well with your trailer wiring.

You will need a Straight 3-Wire Pigtail # A45PB to wire it into your trailer wiring. The red wire from this harness will run to the turn signal circuit, the black is the tail signal, and the white will ground to the trailer frame on a clean metal surface to complete the circuit.

You might also be interested in purchasing a Grommet for ST33 Series Tall Rectangle Flush Mount Trailer Lights # A33GB to help install this product.

expert reply by: Jameson C

0

Answer 1

For a pigtail harness to use with the part #MC57RB you would want the part #A46PB which plugs right into the back of the light. You could splice two sets of the harnesses together if you wanted to power two sets of lights as well.

view full answer...

Answer 2

The Thinline LED Clearance and Side Marker Light #AL91AB require certain mounting brackets and plugs that are either already installed on the trailer or are available separately. A Right Angle 2-Wire Pigtail #A46PB will work with the Grommet #A91GB…

view full answer...

Answer 3

Hey Lawrence, The black wire on the Optronics LED Trailer License Plate Light #LPL81C1B is going to be your 12v power and the white wire will be the ground. You can either cut the plug off and hardwire the light or use a connector like the #GP-1 or…

view full answer...

Answer 4

I have a couple of good options for you but there aren't any available adapters. Instead you will remove your current pigtails like the Optronics 2-Wire Marker Light Pigtails part #AL42PB. Once removed you add the the 2-Wire Pigtail for Optronics…

view full answer...

Answer 5

The Optronics Grommet #A91GB that you referenced, which is designed to work with the Thinline LED #AL91RB that you were looking at, will install into a mounting hole on the trailer that is 2-7/8 inches across and 1-1/2 inches tall. If you do not have…

view full answer...

Answer 6

For a 4-1/2 inch diameter trailer taillight that can do stop/tail/turn functions we have the part #STL43RB which would work well. For a rubber grommet then we'd need the part #A45GB. Then for a pigtail harness you'd need the part #A47PB. For…

view full answer...

Answer 7

Marker lights do have polarity, but when you use the correct pigtail for the lamp it'll be evident which wire is which. For example, the #MC57RB marker light you referred to uses a #A46PB pigtail. The pigtail will only insert into the back of the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommendations for installing a LED Trailer Light # STL35RB on a 2002 Ranger Trail Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching