Replacement Vent Lid Recommendation Where Seal for Vent Cover is 13 by 13 inch

Question

Question:

Is there a white one?

asked by: Eliseo

0

Expert Reply:

Can you send me a picture of the vent you have? 13 by 13 is smaller than what we normally carry but I may be able to take a look and come up with a solution.

expert reply by: Jameson C

0

click to enlarge

Eliseo

5/23/2018

Here are the pictures you requested Sorry it took so long to get back to you. Any help would be greatly appreciated.

Jameson C.

5/23/2018

Thanks for the picture! The replacement lid cover you need is the part # BV0554-03.

Eliseo

5/24/2018

Is there a white one?

Jameson C.

5/24/2018

Yes there is. For that you'd need the part # BV0554-01.

Answer 1

The correct replacement shroud for your Dometic Duo-Therm 600315.321 (Looks like you added an extra 3 at the beginning which is what was likely causing your search issues) is the Replacement Shroud #AT3308046006 you were looking at.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Vent Lid Recommendation Where Seal for Vent Cover is 13 by 13 inch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching