Instructions for Trimming Under Body Panel on a BMW 1 Series 135i
Updated 06/20/2011 | Published 06/17/2011
Products Featured in This Question
Question:
Concerned about trimming the rear bumper cover and it not appearing professional. What is the best way to do this?
asked by: Jeff B
Expert Reply:
The under body panel that needs to be trimmed is at the rear of the vehicle underneath behind the rear fascia. The rear fascia itself will not need to be trimmed. Detailed trimming information is provided in the installation instructions, see drawing and instructions link.
The best way to trim these parts is to take them off the vehicle and use a Dremel with cut off disc. A steady hand is required, and the edges can be touched up with a small file. A razor knife is also an option, but requires careful operation to avoid slipping and scarring areas not to be removed.
Some items you may need to complete your Class I towing setup are listed below.
Hitch Ball 1-7/8 inch, item # 19256
Hitch Ball 2 inch, item # 19258
Hitch Pin, item # PC2
Wiring, item # 119178KIT
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Q&A: How to Install the Curt Trailer Hitch Receiver on a 2013 BMW 128i
- Q&A: Muffler of 2010 BMW 1 Series Rattles Against Recently Installed Hitch
- Q&A: Where Are Fascia Removal Tabs Located on 2012 BMW 128i
- Shop: Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit - Custom Fit - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Towing Kit w/ Ball Mount and Trailer Wiring for Stealth Hitches Hidden Rack Receiver - 2" Ball
- Shop: Quick Splices - Self-Stripping Connector - Closed Port - 14-16-18 Gauge - Blue - Qty 1
- Search Results: hitch pins and clips
- Search Results: two balls trailer hitch ball mount
- Search Results: trailer hitch ball
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Search Results: trailer hitch ball mount
- Article: How to Choose the Right Trailer Hitch Class
on Trailer Hitch
