Muffler of 2010 BMW 1 Series Rattles Against Recently Installed Hitch
Updated 07/02/2020 | Published 12/28/2013
Question:
I followed the instructions step by step. This isnt my first hitch installation. When I drove it for the first time after the install I noticed that the exhaust sounded louder. After further inspection it seems that once the car warms up the 4mm gap between the muffler mount and the hitch closes. This causes the muffler to rest against the hitch. Ive Googled to see if anyone else has experienced the same thing but I havent found a solution. Any ideas on what needs to be adjusted so the muffler mount and hitch arent rubbing? Thanks, Kevin
asked by: Kevin W
Expert Reply:
I have not had any specific feedback on that vehicle, but having a muffler rattle against a hitch is a fairly common occurrence that is easily repairable.
Because an exhaust system is meant to move on its hangers, it does not sit in a fixed position, and this position can vary a bit from vehicle to vehicle. If you look at the FAQ article I have linked you to, you can see some different strategies like slightly bending the exhaust hangers to provide more clearance between the hitch and muffler.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Video: Mount: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector on a 2014 BMW 3 Series
- Q&A: How to Install the Curt Trailer Hitch Receiver on a 2013 BMW 128i
- Q&A: Instructions for Trimming Under Body Panel on a BMW 1 Series 135i
- Q&A: Where Are Fascia Removal Tabs Located on 2012 BMW 128i
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Towing Kit w/ Ball Mount and Trailer Wiring for Stealth Hitches Hidden Rack Receiver - 2" Ball
- Shop: Quick Splices - Self-Stripping Connector - Closed Port - 14-16-18 Gauge - Blue - Qty 1
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Search Results: trailer tires and wheels
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Brake Controller
- Q&A: Clearance Differences Between Hitches For A 2026 Honda Odyssey EX-L
- Video: Clean Up Your Trailer Wiring
on Trailer Hitch
Peter Q.
6/28/2020
Just installed the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" on my 2015 Toyota Rav4. I am noticing a rattle with the muffler. During the installation video, you removed an extra hook. you never indicated that you put it back on install. I tried both ways (installed and not) and still experience a constant rattle. Any recommendations? Thank you