Using the Rhino Rack Nautic 581 Kit on Rhino Rack HD Bars

Question

Question:

Will the 581 rhino yak holders mount to rhinos HD square bars?

asked by: Jeff

0

Expert Reply:

The Rhino Rack Nautic Rear Loading Carrier, part # RR581 will fit your Rhino Rack HD square bars if you add the HD Fitting Kit, part # HD-FK2. These will replace some of the mounting parts included with the Nautic to fit your HD bars.

expert reply by: Jacob W

0

Answer 1

Hey Jake, you probably already have had your Rhino-Rack Nautic 581 Kayak Roof Rack #RR581 show up and have test fit it but the T-bolts of this rack are the size that the top channels of your 2022 Mazda CX-30 have so this rack would work for you. Have…

view full answer...

Answer 2

I went ahead and called my contact at Rhino-Rack, and they confirmed that the Nautic 581 carrier #RR581 has a maximum weight rating that is the same as the roof rack system that you mount it on. Most of the time, roof racks are rated above 99 pounds.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

Hello again Monty; I would get the black SumoSprings Custom Helper Springs #SS66PV. These have a capacity of 1,800 lbs so it gives you a bit over the blue without overdoing it. SumoSprings are a great choice if you don't want to go with the air…

view full answer...

Answer 7

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 8

Hey Scott, congrats on the new truck. I checked with Timbren's website and they do not go into specifics on how many spacers or what size you're going to need. The instructions for the Timbren Suspension Enhancement System item #T45MR say to…

view full answer...

Answer 9

Hey Eric, the K-Source Tow Mirrors part #KS48NQ that you referenced will fit your 2025 Toyota Tundra Platinum as long as it doesn't have extendable or telescoping mirrors. What are you towing?

view full answer...

Answer 10

Hey Chad, Good question and you will need spacers for your 2024 Toyota Tundra with the factory lift when installing the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL24JQ. The rear lift on the Tundra is 2 inches…

view full answer...

Answer 11

I checked with Timbren, and the overall height (from the top of the bracket that bolts to the frame to the bottom of the spring) is 6 inches for the Timbren Suspension Enhancement System #T45MR.

view full answer...

Answer 12

Hello David, thanks for reaching out. Between the TImbrens and the SumoSprings for your 2024 Toyota Tundra I definitely recommend the Sumos. They have a progressive spring rate so you don't get as rough of a ride when you are unloaded. Since your…

view full answer...

Using the Rhino Rack Nautic 581 Kit on Rhino Rack HD Bars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching