Inside Width and Outside Height of the Bike Rack Adapter # CC-125

Question

Question:

My tire is about 2 inches wide. Will it fit in this bike rack? Also, how high does it stick up?

asked by: Lawrence

0

Expert Reply:

I went out to the warehouse and found that the Bike Rack Adapter # CC-125 that you referenced has an inside to inside measurement where your tire will sit is just under 2-1/2 inches.

From the ground to the top of the wheel mount measured about 11 inches.

I have attached a photo for demonstration.

expert reply by: Jon G

0

click to enlarge

Art B.

9/6/2020

I have 4 inch tires, what do you recommend?

Jon G.

9/9/2020

In your case you're going to need to go with a bike rack that can accommodate fat tires as opposed to this carrier. You can go with the Swagman Dispatch # S44FR and use the Fat Bike Adapter Kit # S64694 for each bike with fat tires.

Answer 1

Hey Tom, thanks for reaching out! We have the Bike Rack Adapter #CC-125 that was made for the Stromberg Carlson cargo carrier, but it's pretty universal so as long as your carrier has a mesh base this will work. Most carriers don't have a…

view full answer...

Answer 2

Hey Dennis! I can't say if it will clear for sure but I can give you dimensions to help determine if it will. Using the furthest hitch pin hole, the Malone 2" Dual Purpose Hitch Receiver #MPG544 will push the bike rack out 12-1/4". When…

view full answer...

Answer 3

Hi Ron; looking at pictures you have the right kind of bumper on the rear of your 2023 Entegra Vision 29S. However, I would go ahead and measure it just to make sure the 24x84 etrailer Cargo Carrier #e96ZR will fit. This is designed to for 4" x…

view full answer...

Answer 4

Hey Steven, how heavy are the e-bikes? We have something similar to what you are looking for with the Thule Insta-Gater Pro Truck Bed Bike Rack #TH93VR which normally attaches to truck bed floors but it would also work in the bed of a trailer. It has…

view full answer...

Answer 5

Hey Lawrence, thanks for reaching out. The Curt T-Connector #C56040 is correct for the 2025 Subaru Forester Hybrid. The factory harness plug should be in the rear cargo area behind the driver side access panel. If you remove the trunk floor covering…

view full answer...

Answer 6

Hey Nelson, welcome back and congrats on your new SUV! We get our information directly from Curt and their item #C13409 and item #C47HR hitches fit all models of the 2025 Subaru Forester including the hybrids. This is why we don't list a hybrid…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Patti, thanks for reaching out. The Swagman E-Spec Pro Bike Rack #S45SR is a solid option for this. It can hold two bikes weighing up to 70 lbs apiece on a 5th wheel, and it does not have a minimum tongue weight capacity limitation like the…

view full answer...

Answer 10

No, it will not Mayra. The Universal Wheel Holder Kit item #HR89FR is designed to replace the wheel holders on the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes item #HLY84FR. This is a custom fit replacement part so it's not…

view full answer...

Inside Width and Outside Height of the Bike Rack Adapter # CC-125

Product Page this Question was Asked From

Continue Researching