Is the Shank for B&W Tow & Stow 3-Ball Mount # BWTS10049B Solid or Hollow

Question

Question:

Is the shank on this ball mount solid or hollow?

asked by: Matt

0

Expert Reply:

The shank of the B&W Tow & Stow 3-Ball Mount # BWTS10049B is hollow. For a 3-ball mount that does have a solid shank we have # DT-ALBM6800-3S though it is a different design.

expert reply by: Michael H

0

Answer 1

Some couplers can be adjusted so that the wedge will grab the trailer ball more tightly, but since the coupler you're using has no adjustment available, I'd first confirm that you are using the correct trailer ball size for your coupler. The…

view full answer...

Answer 2

According to the good folks at Demco, you can expect to have as much as 3/4 of an inch of vertical play in a 2-5/16 inch coupler like the Demco #DM15633-81 without having an issue. This is necessary, otherwise you could have problems when trying to…

view full answer...

Answer 3

Hello Bill, thanks for reaching out. I cannot say I have ever heard a complaint about a Demco Ez-Latch Coupler like part #DM37ZR failing and coming disconnected. I ran your question by a group of my associates here and not one of them could recall…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Is the Shank for B&W Tow & Stow 3-Ball Mount # BWTS10049B Solid or Hollow

Product Page this Question was Asked From

Continue Researching