How to Wire the LED Trailer License-Plate Light # LPL55CB

Question

Question:

i do not know how to spice into the current light to bring the plate light to operate on my trailer.

asked by: Dan

0

Expert Reply:

You will need to use a quick splice, item # SWC502905-1, and splice the black wire from the LED Trailer License-Plate Light, item # LPL55CB, into the taillight wire on your trailer. The taillight wire is normally the brown wire, but you should use a circuit tester, item # PTW2993 if needed, to be sure you are splicing into the correct wire.

You will then need to attach the white wire to ground, usually the trailer frame or the white wire coming from the trailer connector.

Once wired the license plate light will illuminate your plate anytime you have the vehicle tail lights on.

expert reply by: Robert G

0

Answer 1

The Optronics LED Trailer License Plate Light with Bracket #LPL56CB uses 20 gauge wire. This thin wire is all that is needed to power the led light as it only draws 0.045 amps at 12.8 volts.

view full answer...

Answer 2

The Brophy 2 inch hitch ball #CB26C is made in the USA. It is rated for 7,500 pounds and has a shank length of 2-1/4 inches and shank diameter of 1-1/4 inches. Convert-A-Ball interchangeable ball set #901b has a 2 inch ball as part of the set. It is…

view full answer...

Answer 3

The license plate light of a trailer will need to tap into the running light circuit of your trailer wiring. The white wire of the light will be the ground and would need to get ran to the frame of the trailer and the black wire will be the power…

view full answer...

Answer 4

The Kenda Karrier ST185/80R13 Radial Trailer Tire - Load Range D #AM10208 is made overseas, and there are none available in that size we offer made in the USA or Canada.

view full answer...

Answer 5

I will start by sating that the wheels/tires on the trailer you are looking at do look kind of undersized. So you definitely can stay with a 13" set up like the Kenda Karrier ST185/80R13 Radial Trailer Tire - Load Range D #AM10208 and Dexstar…

view full answer...

Answer 6

Yes, as long as the actual tire size is the same, a radial ply tire like the Kenda ST185/80R13 #AM10208 will fit onto the wheel just the same as the bias alternative #AM1ST79 it's replacing. Radial trailer tires differ from bias models due to the…

view full answer...

Answer 7

To wire an illuminated license plate holder such as the Optronics LED #LPL55CB, you can simply splice into the running light circuit and ground wire from the trailer connector. I recommend using the 2 Wire Loop #9651P to make these connections. This…

view full answer...

Answer 8

The Replacement Red Lens for Petersen Pedestal Mount Tail Lights #338-15R for the Petersen Trailer Tail Light #429005 snaps in.

view full answer...

Answer 9

Your spindle should have a Washer #SW1000 between the outer bearing and the Spindle Nut #165686. As this part is typically always reused that is the reason it is not included in the Bearing Kit #BK1-150. Instead we only include the cotter pin and…

view full answer...

Answer 10

You can get away without a spindle washer but you may as well install one since you have it apart like with the #SW1000 which is for the standard 1 inch spindle size.

view full answer...

Answer 11

For castle nut #165931, for a D washer use part #5-23 or round washer use part #SW1000. These are both for 1 inch spindles but are compatible with the 7/8 inch castle nut assemblies. You can also use the Replacement Spindle Washer - Tang Type for E-Z…

view full answer...

Answer 12

You can wire a license plate light like part #LPL55CB without running wiring up to the front of the trailer. You simply attach the white wire with the ring terminal to a clean, bare metal surface like the trailer frame, and then attach the black wire…

view full answer...

How to Wire the LED Trailer License-Plate Light # LPL55CB

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching