Replacement for Missing Spindle Washer Used with Bearing Kit BK1-150 and Castle Nut
Published 11/15/2023
Products Featured in This Question
Question:
Bk1-150 has the correct bearing, race, and seal but I dont think that washer will work. My dexter axle isnt the ez-lube model. It has just a castle nut and cotter pin. I think the previous own forgot to put the washer on. Or should the castle nut be up against the bearing? If it should have a washer do you know which one?
asked by: Travis H
Expert Reply:
Your spindle should have a Washer # SW1000 between the outer bearing and the Spindle Nut # 165686. As this part is typically always reused that is the reason it is not included in the Bearing Kit # BK1-150. Instead we only include the cotter pin and D-washer since the cotter pin and D-washer can break. You will be able to discard the D-washer since you have the castle nut style spindle and do not need that part.
Product Page this Question was Asked From
Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Trailer Bearings Races Seals Caps
- Bearings
- Bearing Kits
- Standard Bearings
- Bearing L44649
- Race L44610
- 1000 lbs Axle
- 2000 lbs Axle
- 2200 lbs Axle
- etrailer
more information >
Continue Researching
- Video: Let’s Check Out the Washer For 1" Spindle
- Q&A: Does Grease Seal in Trailer Hub Need to Press Against Bearings in Hub
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Search Results: l44643
- Search Results: safety chain
- Search Results: spindle washer
- Search Results: trailer coupler latch
- Search Results: bearings
- Search Results: coupler latch
- Shop: Timken Bearing Kit, L44643 Inner/Outer Bearings, L44610 Inner/Outer Races, 204507 Seal
- Video: Spindle Grease Seal Set for L44643 Inner Bearing and 1.980 Bearing Buddy Spec Review
- Shop: Bearing Buddy Bearing Protectors - Model 1980A w/ Auto Check - Chrome Plated (Pair)
- Shop: Timken Replacement Trailer Wheel Bearing - L44643
- Shop: Washer For 1" Spindle
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Search Results: hub
- Shop: Trailer Wiring
- Q&A: How Does The Replacement Red Lens For Petersen Pedestal Mount Tail Lights Install?
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Q&A: Does Trailer Hub Without Spindle Washer Need to Have One Installed
- Q&A: Washers Compatible With 7/8 Inch Castle Nut
- Q&A: How to Wire the LED Trailer License-Plate Light # LPL55CB
- Video: All About the Trailer Idler Hub Assembly for 2,000-lb Axles
- Q&A: Recommended Idler Hub Assembly for 1-1/16 Inch Diameter Spindle With Seal 1-1/4 Inches at Spindle
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Video: In-Depth Review of the Replacement Race for L44643 and L44649 Bearings
- Video: Feature Review 2" Square Trailer U-Bolt (Qty 2)