How Does The Replacement Red Lens For Petersen Pedestal Mount Tail Lights Install?

Question

Question:

Does the lens screw on or snap on ?

asked by: Don D

0

Expert Reply:

The Replacement Red Lens for Petersen Pedestal Mount Tail Lights # 338-15R for the Petersen Trailer Tail Light # 429005 snaps in.

expert reply by: Bryce D

0

Answer 1

You can get away without a spindle washer but you may as well install one since you have it apart like with the #SW1000 which is for the standard 1 inch spindle size.

view full answer...

Answer 2

For castle nut #165931, for a D washer use part #5-23 or round washer use part #SW1000. These are both for 1 inch spindles but are compatible with the 7/8 inch castle nut assemblies. You can also use the Replacement Spindle Washer - Tang Type for E-Z…

view full answer...

Answer 3

Your spindle should have a Washer #SW1000 between the outer bearing and the Spindle Nut #165686. As this part is typically always reused that is the reason it is not included in the Bearing Kit #BK1-150. Instead we only include the cotter pin and…

view full answer...

Answer 4

You will need to use a quick splice, item #SWC502905-1, and splice the black wire from the LED Trailer License-Plate Light, item #LPL55CB, into the taillight wire on your trailer. The taillight wire is normally the brown wire, but you should use a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Does The Replacement Red Lens For Petersen Pedestal Mount Tail Lights Install?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching