Recommended 15 Inch Trailer Wheel with 6 on 5-1/2 Inch Bolt Pattern and 3.65 Inch Pilot Hole

Question

Question:

I need 15inch trailer rims as compared to your part number AM20514. Mine have a sticker with 17-118 on them. Im looking for this rim in a spike or hole type. Not a vintage look. 6 lug on 5.5inch pattern with a center hole bore of 3.65. Thank you

asked by: Nick

0

Expert Reply:

The Dexstar Conventional Steel Wheel # AM20514 referenced in your question is the only 15 inch wheel with a 6 on 5-1/2 inch bolt pattern we have available that has a 3.65 inch pilot hole diameter like what you are looking for. This is a conventional steel trailer wheel with a weight capacity of 2,600 pounds.

The 15 inch, 6 on 5-1/2 inch bolt pattern wheels we have available with a spoke or modular design, such as the Sendel Series T02 # AM22654, feature a slightly larger pilot diameter of 4.25 inches.

expert reply by: Chris R

0

Answer 1

We do have an option for replacing your Elixir ELX-60. Unfortunately there is not going to be a direct replacement for the converter section. You will need to replace the entire panel with the Progressive Dynamics 4500 Series RV Converter…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

Hey Michael! The 2026 Kia Sportage Hybrid has the 12V battery integrated into the main battery so you won't be making a connection there. What you need to do is run the #C59236 hot lead to the 12V positive jump terminal under the hood. Everything…

view full answer...