Can I Convert Regular Bunks To Roller Bunks
Updated 05/09/2020 | Published 05/30/2011
Products Featured in This Question
Question:
I have a Rolco Trailer is it possible to change over to your bunk roller design. The boat is a 24-6 Cobalt 4,500 lbs. There are 6 bunks supporting the boat: Two 4 sections Two 9 3 sections Two 13 1 sections Can you let me know if this is OK and if I can remove the bolsters and just bolt to the same areas as the existing bunks. Also can your bunk rollers adapt to the right angle of the bottom?
asked by: Tom W
Expert Reply:
Yes, you could convert your Rolco trailer from the wooden bunks to roller bunks. The Boat Trailer Deluxe Roller Bunk, part # DL21741, has a universal mount system that attaches directly to either vertical or horizontal positioned bunk boards that should work on your trailer.
You may also be interested in Boat Trailer Roller Bunk Bracket, part # DL21742, for mounting the roller bunks. You will have to install these at the correct angle for your boat hull as they are stationery.
We also have 4 foot sections that you may be interested in, Boat Trailer Deluxe Roller Bunk 4 foot, part # DL21740.
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers
- Boat Trailer Parts
- Bunks
- Roller Bunks
- Galvanized Steel
- Dutton-Lainson
more information >
Continue Researching
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Search Results: hitch anti~rattle
- Shop: Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers
- Shop: Trailer Hitch
- Shop: TecNiq Contoured Eight Function Box Style Tail Light - Drivers Side
- Shop: Boat Trailer Deluxe Roller Bunk - 4' Long - 10 Sets of 3 Rollers - by Dutton-Lainson
- Shop: Brake Controller
- Video: Dutton-Lainson Roller Bunks for Boat Trailers Water Test
- Shop: Tie Down Roller Bunks for Boat Trailers - 6 Rollers Each - Amber Poly - 5' Long
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: In-Depth Review of the Dutton-Lainson Boat Trailer Deluxe Roller Bunk
- Q&A: Parts Needed to Switch a 98 Shoreland'r Trailer From Rollers to Bunks
- Shop: Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter
- Shop: B&W Anti-Rattle Clamp for 2" Hitch Receivers
- Q&A: Do the Dutton-Lainson Boat Trailer Deluxe Roller Bunks Have to be Installed on Bunk Boards
- Video: Boat Trailer Deluxe Roller Bunk Feature Review
- Video: All About the Boat Trailer Deluxe Roller Bunk
- Video: Best 2022 Subaru Outback Wagon Trailer Wiring Options
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2022 Subaru Outback Wagon
- Video: etrailer Trailer Brake Controller 7-Way RV Upgrade Kit Installation - 2020 Subaru Outback Wagon
- Article: The Basics of Boat Trailer Bunks: Bunks or Rollers?
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Search Results: trailer tires and wheels
- Q&A: Lug Nut Torque Chart for Trailer Wheels
on Boat Trailer Parts
Bob W.
5/7/2020
I have a 2015 Shorelandr LUV2314 bunk trailer. The bunks are 27" off the ground. I need to drop them by at least 4 inches to launch my boat. Would a conversion to rollers do this? Can this trailer be converted to a roller trailer? I have a 2015 Lund Crossover 1675 with a 115 hp Merc. The rear crossbar is welded and does not pivot.