Can Custom Holes be Drilled Into a Redline Pre-Drilled Round Rubber Bumper

Question

Question:

Hi, I am needing a rear rubber trailer bumper but the 2 pre-drilled hole patterns doesnt match my trailer. Can those bumpers be drilled with different pre-drilled hole patterns? Thanks

asked by: Skip R

1

Helpful Expert Reply:

Since the Redline Pre-Drilled Round Bumpers, part # D3-96, part # D2-96, and part # D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches of the bumpers then you may want to consider drilling more mounting holes in your trailer so that the bumper has more support. I recommend drilling out holes to match the rest of the pre-drilled holes to avoid more drilling.

Keep in mind that you will need to supply your own mounting hardware.

expert reply by: Jon G

1

Answer 1

We have 3 different rubber bumpers that you can use for your horse trailer. They all measure 96" long but have different widths so you'll just need to choose the appropriate width: 2-1/16" Width - #D2-96 3" Width - #D3-96 4"…

view full answer...

Answer 2

The Pre-Drilled Round Rubber Trailer Bumper #D3-96 weighs 21lbs. It is 96" long, 3" wide and will stand 3" tall.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

Answer 9

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 10

Louie, Yes, that is a great question. You do not have to worry about the air bags interfering with your B&W Turnoverball hitch setup. The Firestone Ride-Rite Air Bags with Easy Mount Compressor and In-Cab Control #F84XV are compatible with in-bed…

view full answer...

Answer 11

Hey Paul! The PullRite SuperGlide #PUL43RR (2714) and #PUL73RR (2914) do weigh the same. The main difference is the capacity, which is going to come from the base of the 5th wheel hitch. Since your 2027 Keystone Cougar 316RLS has a GVWR of 12,900 lbs…

view full answer...

Can Custom Holes be Drilled Into a Redline Pre-Drilled Round Rubber Bumper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching