Tang Washer for 1-1/6 Inch Spindle

Question

Question:

I'm looking for tang washers for 1-1/16 inch spindles. Do you have them?

asked by: Amit K

0

Expert Reply:

We do not have tang washers for 1-1/6" spindles, however, it is possible you might need a washer for a 1" diameter spindle, because 1-1/6" is the same diameter as bearing # L44649, which goes to 1" spindles. I recommend double checking with a digital caliper just to make sure you don't need a 1" washer such as Replacement Spindle Washer - Tang Type # 5-101.

I've added a link to our page with each of our spindle washers for you as well.

expert reply by: Kyle S

0

Answer 1

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 2

The Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies part #AKBRKR-M7 and Replacement Trailer Brake Magnet Kit for 7" Brake Assemblies part #BP01-068 are both round brake magnets for 7", 2,000 lb trailer braking…

view full answer...

Answer 3

Hello Mark, The only round magnets we have are the Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies - 2,000 lbs #AKBRKR-M7, and the #BP01-068 which are bot 1 7/8". What is your axle capacity? Can you send in pictures by…

view full answer...

Answer 4

JC, the CE Smith Trailer Axle Beam with Standard Spindles #CE33201GA definitely should've came with spindle nuts so I'd reach out to our customer service team about that. This axle uses the Trailer Spindle Nut 1" #165686 with the Washer…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Hi Dan; is there a tag on the axle? That would be the only real way for me to identify it for sure. I'm guessing you would have an old metal tag which should have a serial number. You could also check on the axle itself for a serial number…

view full answer...

Answer 7

It is acceptable and highly water insoluble so it is great for boat trailers. Grease like the LubriMatic LMX Industrial Strength Grease #L11390 is a lithium complex. The same is true for Lucas Red N Tacky which means they are compatible.

view full answer...

Answer 8

On a trailer electric brake assembly like the Dexter 6,000 Pound #23-105 you were looking at the magnet itself should be at the bottom. The arm that is attached to the magnet should then be located on the front side of the trailer (towards the…

view full answer...

Answer 9

Since you don't have the D-shaped spindle that will allow for a D washer, a regular washer for a 1 inch spindle like #SW1000 will work. This washer not having any type of tab will allow it to rotate and without proper grease could cause damage as…

view full answer...

Answer 10

It sounds like you might be searching for some replacement electric trailer braking assemblies or possibly just replacement parts. It's typically not much less cost effective to just replace the entire assembly so that's what I recommend. I…

view full answer...

Answer 11

The default speed rating for a trailer tire is 65-mph. When the tire can handle higher speeds we will explicitly call this out in the tire specs. If we do not indicate a speed rating then it is 65-mph. In the tire size ST205/65-10 we offer four…

view full answer...

Answer 12

That's a great question! Let's find out together Jerry. The 4.80x12 tires currently on your trailer measure 20.5" in diameter and are 4.9" wide. The 20.5x8x10 which is equivalent to a 205/65-10 tire like item #AM1HP56 is 20.4"…

view full answer...

Tang Washer for 1-1/6 Inch Spindle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching