Installation of B&W Extend-A-Goose Gooseneck Coupler
Updated 08/08/2017 | Published 08/07/2017
Question:
Hello, Recently we received our TEXA400 10inch extender for our gooseneck trailer. The pin holes are side to side on the device but the pin holes on my trailer are front to back. Maybe I just am looking at it wrong but I cannot figure out how to install this on my trailer especially given the hole placements. There are a ton of videos but all showing the installation on the truck side. Maybe you have one from the trailer side? I am sure you can straighten me out... I am sorry if I am just not looking at this right. thanks for the help
asked by: Wendy S
Expert Reply:
Yourr trailer's coupler uses set screws to hold the tube in place instead of a cross pin. In this case you'll still use the set screws in the same fashion they're being used to install the Extend-A-Goose # BWTEXA4200 and you won't use a cross pin through the pin holes.
Product Page this Question was Asked From
B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset - 24,000 lbs
- Gooseneck Coupler
- Coupler with Inner Tube Only
- Round Tube
- 10 Inch Offset
- 24000 lbs GTW
- 2-5/16 Inch Gooseneck Ball
- Manual Latch
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: A Closer Look at the B and W Extend-A-Goose Gooseneck Coupler
- Search Results: saftey chains
- Video: What to Know About the B and W Extend-A-Goose Gooseneck Coupler
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Shop: B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset - 24,000 lbs
- Shop: Dexter Self-Contained Hydraulic Jack - Square Tube - 20" Lift - 10,000 lbs - Bolt On
- Shop: Safety Chain Kit for Shocker Hitch 5th Wheel to Gooseneck QuickAir Hitch - 42" Long - 24K lbs
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: etrailer Electric Trailer Jack w/ 7-Way - Drop Leg - A-Frame - 18" Lift - 5,000 lbs
- Shop: Square Direct Weld Trailer Jack - Drop Leg w/ Spring - Sidewind - 15" Lift - 12,000 lbs
- Q&A: Pin Hole Dimensions In B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200
- Q&A: Purpose Of Offset Holes On B And W Extend-A-Goose Gooseneck Coupler
- Q&A: Is It Ok For The B&W Extend-A-Goose Gooseneck Coupler To Sit Slightly Crooked Once Installed
- Q&A: Vertical Rise To Welds and Lowest Pin Hole on B&W Extend-A-Goose Gooseneck Coupler
- Q&A: Recommended Gooseneck Hitch And Wiring For 2012 Ford F-150 With 5-1/2 Ft Bed
- Q&A: Availability of 30k Rated Gooseneck Couplers
- Q&A: Offset Gooseneck Coupler Needed for 2022 Ram 3500 Mega Cab with 6'4” Box
- Search Results: extend a goose
- Search Results: gooseneck ball extender
- Article: How to Replace an RV Roof Vent Cover
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer wiring
on Gooseneck Coupler
