How to Pick Out Install Hardware for Plunger and Rubber Socket Door Holder # PLR62-66

Question

Question:

I just received the PLR62-66 plunger and rubber socket for my trailer. What bolts or screws are recommended for installation? Thanks.

asked by: Jon D

0

Expert Reply:

Really it depends on your application. Best option would be to check out where you want to install the plunger kit and decide if wood screws or nut and bolt would work best. Once you make that decision consider the depth you'll need and then take the plunger with you to the hardware store to find the correct length and style bolts that will fit in the mounting holes.

expert reply by: Jameson C

0

Answer 1

The Redline Pre-Drilled Round Rubber Bumper #D2-96 can be installed in a variety of ways depending on the nature of the trailer. The holes are drilled all the way through to allow user-supplied hardware to mount it. We also offer a larger size bumper…

view full answer...

Answer 2

As noted in this item's specs, the mounting holes in the plunger part are spaced at 2-inches center to center. The holes in the receiver/socket part are spaced at 2-1/2-inches.

view full answer...

Answer 3

I've seen rubber socket/plunger kits like the part #PLR62-66 on the bottom of the doors more frequently than the top. That could very well be because it's easier to install them lower though. If you prefer them at the top there's no…

view full answer...

Answer 4

The mounting bracket holes can vary by manufacturer but 1" x 2-1/4" is super common. To install the T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer #37210525 you can reuse the 1" spaced holes and one set of the holes…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Brian, To flat tow your 2026 Ford Ranger XLT with your Blue Ox Avail Tow Bar, you'll need: - Blue Ox Base Plate Kit w/Removable Arms part #BLU77ER, this will require some minor drilling, and the tow hooks must be removed and remain off the…

view full answer...

Answer 7

Hey Rik, thanks for reaching out. The first thing I’d check is that each clamp is fully engaged and sitting flush against the underside of the Ranger’s bed rail. The Fas-Top side rails need to be seated firmly against the bed before the clamps are…

view full answer...

Answer 8

Hey Scott! Your 2026 Ford Ranger may or may not have a brake controller port/plug, even with the tow package. There will be four wires coming out of a large wire harness by the driver side firewall, left of the brake pedal, which can be wired to the…

view full answer...

Answer 9

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 10

I sure can Scott! I verified with Roadmaster that their Direct-Connect Base Plate Kit item #RM23DQ does fit the 2026 Ford Ranger Raptor. It can indeed be flat towed and there are no other restrictions. This baseplate kit comes with all hardware…

view full answer...

Answer 11

Hi Richard! I see you placed an order already, but I still wanted to get you an answer to your question. With that said, the RM-15267 wiring kit isn't going to work with the LED lights on your new 2026 Ranger. For that, you will want the…

view full answer...

Answer 12

Hey Richard. Yes, the Roadmaster Brake-Lite Relay Kit for Towed Vehicles item #RM-88400 is exactly what you need to get the lights on your 2025 Ford Ranger synched up with the functions on your RV. I've linked an installation video below along…

view full answer...

How to Pick Out Install Hardware for Plunger and Rubber Socket Door Holder # PLR62-66

Product Page this Question was Asked From

Continue Researching