How to Install Redline Pre-Drilled Round Rubber Bumper # D2-96

Question

Question:

I would like to know what type of bolts you need to mount this bumper as my trailer did not have a bumper already installed. Also, is there a special socket or some other tool I need?

asked by: Tim

0

Expert Reply:

The Redline Pre-Drilled Round Rubber Bumper # D2-96 can be installed in a variety of ways depending on the nature of the trailer. The holes are drilled all the way through to allow user-supplied hardware to mount it.

We also offer a larger size bumper # D3-96 that measures 3-inches x 3-inches.

No special tool is required for installation; you will use whatever tool is appropriate for the fasteners you choose.

expert reply by: Adam R

0

Answer 1

I spoke with my contact at High Country Plastics and she said that the Horse Trailer 25 Gallon Water Caddy #SL-25 is constructed of low linear density polyethylene. If you or somebody you know can plastic weld you should be able to repair the hole…

view full answer...

Answer 2

What you'd want to do is drill holes in the Pre-Drilled Round Rubber Trailer Bumper #D3-96 to match the mounting holes of your trailer and you'd be set. The bumper is rubber so it would be easy to drill. The pre drilled holes of this are 11…

view full answer...

Answer 3

You could use some self-tapping screws like #FA1131822 to avoid drilling holes first. If you know about where the wiring is you could position the bumper #D3-96 so as to avoid the wiring. Or another option would be to drill from the backside, if…

view full answer...

Answer 4

We do have some rubber bumpers for you to install on your stock trailer. They are all 96" long so it just depends on what kind of width you're looking for: 96" Long x 2-1/16" Wide - #D2-96 96" Long x 3" Wide - #D3-96…

view full answer...

Answer 5

Yes, you would want a Replacement Cap for 25 Gallon Corner Water Caddy Stand ZC-100638-N to replace the cap of your Horse Trailer 25 Gallon Water Caddy #SL-25.

view full answer...

Answer 6

Since the (presumably steel) material on your trailer is 2 inches thick drilling it for installation of the Redline Round Rubber Bumper #D3-96 is not a great option since this would require a lot of drilling time and extra-long hardware to install…

view full answer...

Answer 7

Really it depends on your application. Best option would be to check out where you want to install the plunger kit and decide if wood screws or nut and bolt would work best. Once you make that decision consider the depth you'll need and then take…

view full answer...

Answer 8

To hook up a trailer jack to a 12 volt battery you need to make the connection from the jack's power wire to the positve post on the battery using a ring terminal, like part #DW05705-1. If you don't already have a battery on the trailer you…

view full answer...

Answer 9

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as possible go…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How to Install Redline Pre-Drilled Round Rubber Bumper # D2-96

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching