Replacement Fan Blade Compatible With Maxxair Vent Fan

Question

Question:

I have a maxair ceiling vent, i only need the blade. is the blade the same size as the blade on the ventline. or do you carry the blade for the maxair.

asked by: Eugene R

0

Expert Reply:

We don't have a Maxxair fan blade replacement, however the Replacement Fan Blade for Ventline Ventadome Trailer Roof Vents # BVD0215-00 or # BVE0114-00 are possible options. These blades are smaller than the Maxxair vent fan blades, so more blades will help move the air.

expert reply by: Jason S

0

Answer 1

Hey Scott, yes the MaxxAir Fan Blade #MA49MR that you referenced does fit your Maxxair Plus 4751KS as it fits all Maxxair RV Roof Vents including what you have. Is only the fan blade of your roof vent damaged?

view full answer...

Answer 2

We can confirm for you that the part #BVE0114-00 that you referenced has a 5 inch diameter like you are in need of.

view full answer...

Answer 3

Motor #BVD0218-00 should be the correct replacement. The motor comes with new wires, a bracket, and hardware. The screws that hold the motor to its bracket can be accessed by removing the fan blade. It should just pull off of the motor shaft. You…

view full answer...

Answer 4

For your Ventline E-Z Ventadome Trailer Roof Vent #V3094-601-00, the correct replacement fan blade is the Replacement Fan Blade for Ventline E-Z Lift Ventadome Trailer Roof Vents #BVE0114-00.

view full answer...

Answer 5

There isn't an add-on fan kit available for your Ventline E-Z Lift Ventadome Trailer Roof Vent #V3092-601-00, but you could still get the motor and fan blade from their 12v models and try to attach it to the support for the lift arm. The motor…

view full answer...

Answer 6

I spoke with Lippert about the mounting brackets for the Lippert On-The-Go Telescopic Ladder #LC64HD and found out that they are only sold as an OEM part. This means that only the motorhome/trailer manufacturer is able to order them so you…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Fan Blade Compatible With Maxxair Vent Fan

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching