Location Of The Grey Fuse Holder Connector On A 2000 Toyota Tundra
Updated 06/23/2026 | Published 07/22/2017
Products Featured in This Question
Question:
Curt T-connector wiring kit #C55367 for my 2000 Toyota Tundra: Cant find the fuse connector on drivers side fender wall...near the battery ?????
asked by: John Q
Expert Reply:
The small grey connector that is attached to the red fuse holder wire on the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # C55367 for a 2000 Toyota Tundra is located in the vehicle's engine compartment between the battery and firewall. It should be a small grey connector with a single prong.
Don't forget to add a bit of Dielectric Grease for Electrical Connectors part # 11755 before mating the connectors. You will also want to use a 4-way mounting bracket such as the Mounting Bracket 4-Pole Flat part # 18144 if you do not already have one.
I have attached a photo of this location for you.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Powered Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Visible
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Brake Controller
- Search Results: dielectric grease
- Q&A: Recommended Hitch and Wiring Harness for a 2000 Toyota Tundra
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: curt 51500
- Search Results: brake controller
- Search Results: curt 57672
- Search Results: circuit breaker
- Search Results: go power
- Q&A: Custom Wiring Harness for a 2000 Toyota Tundra To Tow a Boat Trailer
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Shop: Trailer Hitch
- Video: DIY Install: Tekonsha Prodigy P2 Trailer Brake Controller on your 2002 Toyota Tundra
- Shop: Curt Universal Wiring Kit for Trailer Brake Controllers - 10 Gauge Wires
- Shop: Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge
- Q&A: Installing a 7-Way Trailer Connection on a 2000 Toyota Tundra
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - Off-Road Mode - Up to 3 Axles - Proportional
- Q&A: 2000 Toyota Tundra Hitch Replacement and Towing Capacity
- Q&A: Installing Trailer Wiring Harness On 2000 Toyota Tundra
- Video: Checking Out the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C55367 Review
- Q&A: Where Does Curt Trailer Wiring Harness Install on a 2000 Toyota Tundra
- Q&A: Comparing The Curt And Hopkins Trailer Wire Harnesses For A 2000 Toyota Tundra
- Video: Set up: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness on a 2019 Nissan Armada
- Video: Review of the Go Power Overlander Solar Charging System with Digital Solar Controller
- Video: Comparing the Tekonsha Prodigy P3 and Redarc Tow-Pro Liberty Brake Controllers
- Video: Making sure the Redarc Tow-Pro Liberty Brake Controller Fits
on Custom Fit Vehicle Wiring
Abel
5/11/2026
ON MY 2000 TUNDRA AT THIS LOCATION THERE IS A 2 POLE CONNECTOR ON BOTH MALE AND FEMALE ENDS. THE CONNECTOR YOU SEND IN THE KIT IS A ONE POLE AND DOES NOT WORK