Comparing the Receiver to Bumper Clearance for Trailer Hitch Receivers for a 2015 Toyota Corolla

Question

Question:

Thanks! What draw bar would you recommend I get? I like the euro style ones.

asked by: Joel

0

Expert Reply:

I will go ahead and give you the measurement for the 2 hitches that are a confirmed fit for your 2015 Toyota Corolla.

From the center of the hitch pin hole to the outermost edge of your bumper will be as follows:

Curt # C11265 - 3 inches
Draw-Tite # 24913 - 2 inches

Since they all have 1-1/4 inch receivers it really just depends on what you are planning to use the hitch for when it comes to deciding which is best. They all have the same weight capacities and Class I restrictions. (see attached article for restrictions)

Keep in mind that the Curt receiver requires the use of a support strap # 18050 for all non-trailer loads per the Curt warranty.

I have attached videos of each hitch being installed on a similar 2015 Toyota Corolla for you to check out.

expert reply by: Jon G

0

Joel

6/29/2017

Thanks! What draw bar would you recommend I get? I like the euro style ones.

Jon G.

6/29/2017

If you like the Euro style drawbar then I recommend using the Curt Class II Euro Style Drawbar # C45571 with the Curt Hitch # C11265. You will need to measure the Rise and Drop to see if this drawbar option is the correct fit for you though. I have attached an article that explains how to choose a drawbar with the correct Rise or Drop. To finish up your towing setup you will also need some trailer wiring. i recommend going with the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118405 because of how reliable Tekonsha electronics are. I have attached a video of this being installed on a 2009 Toyota Camry that you can use as a reference.

Answer 1

Hey Arnel congrats on the new SUV. So long as your 2026 Honda Passport Trailsport has a 7-way trailer connector the Pollak 7 Pole to 4 Way Connector Adapter item #PK12716 will indeed work. This adapter will plug directly into a 7-way connector and…

view full answer...

Answer 2

Since dirt bike carriers are designed to carry heavier loads all of them have 2" shanks. All of the trailer hitches available for your 2014 Toyota Corolla have a 1-1/4" receiver and so the only way you'll be able to transport your…

view full answer...

Answer 3

For your 2006 Toyota Corolla Sport, I recommend using the Curt Trailer Hitch Receiver part #C11265. This hitch hangs down lower on the vehicle in comparison to the Draw-Tite Sportframe Trailer Hitch Receiver part #24913. As you can see in the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Comparing the Receiver to Bumper Clearance for Trailer Hitch Receivers for a 2015 Toyota Corolla

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching