Which Tire Stem Valve Fits in the Dexstar Conventional Steel Wheel with Offset?

Question

Question:

What is the tire stem size for the Dexstar Steel Wheel?

asked by: Chris

0

Expert Reply:

I went out to the warehouse and measured the rim hole diameter of the Dexstar Conventional Steel Wheel with Offset # AM20304 and the correct stem valve for this would be the Americana # AM20903, which has a rim hole diameter of 0.453 inches.

expert reply by: Kyle S

0

Answer 1

Thank you for the photo showing the fit of your trailer's wheel beauty rings on the original and new conventional steel wheels. I do see that the valve stem on the wheel #AM20304 contacts the ring. This might be a case of the new wheel using a…

view full answer...

Answer 2

I do have a solution for you but we don't recommend using a spacer as that will cause your wheel to sit at a different location on your lugs. The offset of a wheel can be determined by measuring from the mounting surface of the wheel (where it…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Which Tire Stem Valve Fits in the Dexstar Conventional Steel Wheel with Offset?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching