Location of Brake Controller Install Plug on a 2017 Nissan Armada

Question

Question:

I just purchased part # 90195 along with part # 3050-P and am having a little trouble locating where the plug is on my 2017 Nissan Armada to connect part #3050-P? Any help appreciated. Thanks.

asked by: Jason

1

Helpful Expert Reply:

Since you have a 2017 Armada the pre-wiring is on the right side of the steering column, above the accelerator (see pic). This is where you'll plug the part # 3050-P into for the Prodigy P3 part # 90195.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Since you have a 2017 Armada the pre-wiring is on the right side of the steering column, above the accelerator (see pic). This is where you'll plug the part #3050-P into for the Prodigy P3 part #90195. If you currently do not have any trailer…

view full answer...

Answer 2

The standard quick-release mount for the P3 #90195 is the part #TK5906. This would probably be your best option. Actually I checked the reviews for the #7686 and found a customer who said he attempted to get it to fit a P3 and it did not work.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Location of Brake Controller Install Plug on a 2017 Nissan Armada

Continue Researching