Ball Mount with 5 Inch Rise and Compatible 2 Inch Ball for a 2015 Honda CR-V

Question

Question:

I have a 2015 Honda CRV with a class 1 hitch. Im in need of a 2inch ball and appropriate 5inch rise hitch mount. Can you please tell me which products I will need?

asked by: Jim B

0

Expert Reply:

For a Class I ball mount that has a 5 inch rise for your 2015 Honda CR-V you can use # C45024. This particular ball mount can only be used in the rise position. For a compatible 2 inch diameter ball use # C40018.

expert reply by: Michael H

0

Answer 1

What that means is that the Malone MicroSport trailer, part #MPG460G, is level when the bottom of the coupler is 18 inches off the ground. To tow the trailer level you need a ball mount with a rise. Park your Nissan Altima on level ground and measure…

view full answer...

Answer 2

The distance from the center of the hitch pin hole to the backside of the vertical plate is 2.39". I have attached a photo with the measurement for you as well. In order to determine if this ball mount will work with the Draw-Tite Sportframe…

view full answer...

Answer 3

In order to select the correct amount of rise or drop you would need you will need to take a couple measurements. The goal is to have your trailer sit as level as possible. The first thing you will need to do is park your tow vehicle on level ground…

view full answer...

Answer 4

Like you said all of the hi-rise hitch balls have a larger shank diameter than 3/4 inches. They are all either 1 inch or 1-1/4 inch. But depending on how much total rise you need there may be a ball mount you can use that will get you close if not at…

view full answer...

Answer 5

Based on the measurements you took on your trailer hitch and trailer coupler, you will technically need a ball mount that features a rise of around 8-1/2 inches for a completely level setup. Between the two ball mount options you mentioned, the Curt…

view full answer...

Answer 6

The highest rise on a ball mount we currently offer that is compatible with a Class I trailer hitch is the Curt #C45028, which has a rise of 5-3/8 inches. Higher rise ball mounts are only compatible with higher rated hitches. If you need this…

view full answer...

Answer 7

The Curt bar #C45028 (5-3/8 inch rise or 6-inch drop) you referenced is one of 3 Curt drawbars we currently offer that will have a 5 inch or more rise in the shank. The reason other shanks may have a different rise is because it may have a different…

view full answer...

Answer 8

I would be happy to help you out. On the CURT Ball Mount, #C45024, from the center of the hitch pin hole to the near end of the ball mount measures 1-1/2 inches. From the center of the ball hole to the back edge of the ball platform towards the car…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Ball Mount with 5 Inch Rise and Compatible 2 Inch Ball for a 2015 Honda CR-V

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching