Installing A Brake Controller In A 2016 Infinity QX80

Question

Question:

Hi Guys What harness do I require for the DrawTite 5504 for my 2016 Infiniti QX80. Thank you

asked by: Brian S

0

Expert Reply:

If you have a factory 7-way on your 2016 Infinity QX80, then you will only need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti # 3050-P to get your Draw-Tite Activator IV Trailer Brake Controller - 1 to 4 Axles - Time Delayed brake controller # 5504 to function correctly.

If you do not have the factory 7-way, then you will need to start with a 4 way connection. If you don't already have one, I recommend using the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT. This will allow you to capture the signal of your vehicle wiring for your trailer connection without splicing into any wires. The powered modulite will allow the Zero Contact Interface Sensors to transfer the connection to a 4-way flat connection.

You will then use your 4-way connection in conjuction with the Universal Installation Kit for Trailer Brake Controller # ETBC7. This will give you the connectors, wiring, and circuit breakers you need to connect your brake controller and have 7-way trailer connection functions. I've attached videos to help.

expert reply by: Jason S

0

Answer 1

Not a problem. You will need to attach the red brake controller wire to the green/yellow wire (vehicle stop lamp switch). This wire tells the brake controller that you are stepping on the brake pedal. It is a dedicated brake light only signal. The…

view full answer...

Answer 2

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 3

Hey Hailye, I looked up the dimensions of your Predator 9500 and it measures 31 wide x 23.8 deep so the best slide out we have would be the MORryde part #MR89FR which is 33 inches wide and 36 inches deep and has an 800 lb weight capacity. Think this…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hi Joel! The easiest way to install a brake controller on your 2026 Toyota 4Runner would be to use the Redarc Tow-Pro Elite Brake Controller w/Custom Harness part #RED56CR. It is the same Redarc Tow-Pro brake controller as the RED44FR but has the…

view full answer...

Answer 8

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Installing A Brake Controller In A 2016 Infinity QX80

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching