Replacement Parts for Bulldog Powered-Drive Trailer Jack

Question

Question:

I just bought a trailer with this jack installed. The previous owner bent the down tube and destroyed the jack. The motor unit is good and works fine. Is there a replacement for the entire jack portion? Basically everything but the motor unit.

asked by: TimT

0

Expert Reply:

There are few replacement parts available for the Bulldog Powered-Drive Trailer Jack # BD500187 referenced in your question, but they may not be what is needed to completely fix the damaged parts on your existing jack.

For the Replacement Drop Leg and Pin Kit, you will use # BD500190. We also have replacement switches for the extension/retraction and light, parts # BD500363 and # BD500362.

These are currently the only replacement parts available for the Bulldog Powered-Drive Trailer Jack. If the entire down tube is destroyed, then I recommend replacing the entire jack with # BD500187.

expert reply by: Chris R

0

Answer 1

The Electric tongue jack for a trailer is determined by the actual tongue weight of the trailer. Normally this is 10-15% of the total trailer weight when loaded, but a jack is one area where having something rating larger than needed will not cause…

view full answer...

Answer 2

Did you possible over extend the jack? If you let the jack over extend you will destroy the threads of the screw of the and nut which will prevent the jack from being able to go up or down.

view full answer...

Answer 3

The etrailer.com Electric Jack #EJ-3520-WBX has a 1-year warranty on its parts. Replacement parts are sometimes available however not always as common. Atwood has been purchased by Lippert so parts for their jacks are becoming more and more difficult…

view full answer...

Answer 4

All-around the Stromberg Carlson Electric Trailer Jack #JET-5000NG is nicer than the #JET-5000. The bearings in the part #JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is…

view full answer...

Answer 5

Sounds like something loosened itself up after the first trip. I recommend lifting the cover and retightening the bolts on the Stromberg Carlson Electric Trailer Jack item #JET-5000. You'll want to check the mounting bolts too.

view full answer...

Answer 6

Hey Carl, that will depend on a few dimensions on your truck and trailer that we don't know but I can still help. When the jack part #JET-5000 is installed it will be 23 inches above the mounting bracket like you see in the attached picture. If…

view full answer...

Answer 7

I can understand why this must be frustrating but I can tell you that etrailer handles all warranty issues for Bulldog jacks (Horizon Global-Cequent is the parent company). For this reason, if you purchase your Bulldog Powered Drive Trailer Jack -…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Parts for Bulldog Powered-Drive Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching