Adjustable Trailer Hitch for Installation on Frame of Motorhome

Question

Question:

Id like to know the bolt spacing on the frame for the side plates of Draw-Tite 41947. I want to install this on a motorhome chassis that currently has a class III hitch and want to see where the bolt holes wil be compared to the OEM spacing.

asked by: Bob K

0

Expert Reply:

The linked instructions for the custom-fit Draw-Tite Ultra-Frame Class V hitch # 41947 show specific height dimensions from the bottom of the vehicle frame down to the top of the hitch receiver tube. The adjustable side brackets can place the receiver either 6-5/8-, 8-1/4- or 10-1/4-inches below the bottom of the frame rail when this hitch is installed on one of the intended vehicles.

A better option in your application on an RV is to use one of our adjustable-fit frame-mounted RV hitches, all shown on the linked page. All have a 2-inch receiver tube and carry weight capacities up to 600-lbs tongue weight and 6000-lbs gross towing. Just measure your RV's frame width to find the bet fit.

expert reply by: Adam R

0

Answer 1

I spoke with my contact at B and W and he informed me that the center section of the B and W Hitch part #BWHDRH25124 measures 31-13/16 inches long measured from outside of flange to outside of flange.

view full answer...

Answer 2

I recommend a Class V hitch for your Gulfstream that is based on a 1999 Ford F-450 cab-and-chassis. These are available in both 2-inch and 2-1/2-inch receiver sizes and in tow ratings up to 20K. All can be seen on the linked page. All require…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver #C15410 is 37" wide and the bolt hole slots are 34-1/4" on center from drivers side frame rail to passenger side frame rail.

view full answer...

Answer 4

The Curt hitch part #C15400 that you referenced is a confirmed fit for your 2018 Forest River Georgetown GT5 31L5 but it does require drilling which means it does not line up with any current holes on the frame. There aren't any other hitches out…

view full answer...

Answer 5

The two highest rated trailer hitch receivers we have for RV's are both Class III hitches rated for 5,000 pounds gross trailer weight and 500 pounds of tongue weight. Curt hitches #C13702 and #C13701 are adjustable and will fit RV frames from 18…

view full answer...

Answer 6

We have a hitch option for your 2006 Itasca Suncruiser, but the #C15400 is 32.94" wide overall and the bolt holes are 30.31" apart from each other. So what you will need is a universal weld-on hitch, which will fit so long as the frame on…

view full answer...

Answer 7

If the Draw Tite hitch part #41952 has the correct mounting hole dimensions needed for your 2004 IC CE200 bus then there's no reason it wouldn't fit.

view full answer...

Answer 8

Because Cab/Chassis trucks have a narrower 34 inch frame width than the pickup, the Curt #C15860 Class V hitch won't fit your truck, as it'd designed for the wider frame member spacing of the pickup. We do have a Class V option that will work…

view full answer...

Answer 9

I can help you find a hitch that will fit your 34 inch outside to outside measurement on your 2016 Chevy 3500 HD. It sounds like you have a Cab and Chassis style Chevy, because of the 34 inch wide outside to outside frame. I have listed the trailer…

view full answer...

Answer 10

I spoke to my contact at Curt and he informed me that the Curt hitch #C15317 center section measures 31-5/8 inches. The center to center mounting hole width with the flanges attached is 34-7/8 inches. He also informed me that the flanges on the…

view full answer...

Answer 11

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 12

I checked with Curt and they sent me the following dimensions based on your picture for the #C15410. Red line measurement 10.55” Yellow Line measurement 5.32” Green Line measurement is 7.5”

view full answer...

Adjustable Trailer Hitch for Installation on Frame of Motorhome

Featured Help Information

Miscellaneous Media

Continue Researching