B & W Hitch BWHDRH25124 Center Section Width

Question

Question:

Hi, What is the width of the center section, outside of flange to outside of flange?

asked by: Les

0

Expert Reply:

I spoke with my contact at B and W and he informed me that the center section of the B and W Hitch part # BWHDRH25124 measures 31-13/16 inches long measured from outside of flange to outside of flange.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional drawing…

view full answer...

Answer 2

When it comes to installing a trailer hitch on your 2014 Ram 3500 The Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2 inch #15400 is confirmed to fit your 2014 Ram 3500. The Curt Hitch #C15409 is not confirmed to fit your vehicle. This hich…

view full answer...

Answer 3

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 4

I spoke to my contact at Curt and he informed me that the Curt hitch #C15317 center section measures 31-5/8 inches. The center to center mounting hole width with the flanges attached is 34-7/8 inches. He also informed me that the flanges on the…

view full answer...

Answer 5

Thank you for the photo! What you have there is a deep drop or "cowboy" bumper. So, for a 2 inch trailer hitch that is confirmed to fit your 1989 Ford F-250 XLT Lariat with the deep drop bumper, I recommend the Curt #C15511. This 3-piece…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 7

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 8

The Curt Class V 2 Inch Hitch #C15445 is listed to fit a 2011 Ford F-450 Cab and Chassis with 34 inch wide frame. I am sending a link to the installation instructions of the Curt hitch. If you will be needing a pintle hook mount with a long shank I…

view full answer...

Answer 9

So there's one of two things going on here if your Curt 3-Piece Trailer Hitch Receiver #C15511 isn't lining up properly on your 1998 Chevy K3500 pickup. The first possibility, and the most likely, is that the hitch was slightly bent, or…

view full answer...

Answer 10

As long as the 34 inch width dimension you took was from outside to outside on the frame channels the Curt hitch part #C15445 will fit as that's the frame dimensions it was designed to fit.

view full answer...

Answer 11

Because the mounting flange of the Curt #C15511 Class V hitch has 3 tabs on each side, rather than a continuous mounting flange like many other hitches, it'll fit around the rivet shown in your photo. However, be aware that the Curt #C15511 is a…

view full answer...

Answer 12

The width of your frame indicates that your 2012 Ford F-450 is most likely a cab and chassis model which has the frame width a few inches than a standard truck bed. But if you can measure the distance between the mounting holes on the frame of your…

view full answer...

B & W Hitch BWHDRH25124 Center Section Width

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching