LED Amber Colored Trailer Clearance Light with 2 Wire Design

Question

Question:

Does this size and style stud mount LED light come with a lead and ground wire? I didnt want to ground using the stud. If not, do any other brands offer this option?

asked by: Darin H

0

Expert Reply:

The Optronics LED Clearance Light # MCL95AB does ground through the mounting stud.

For a different yet similar light you can use # MCL13A2B with snap-on ring # A13B2B that is a 2 wire light and does have a ground wire.

expert reply by: Charles S

0

Answer 1

The brown wire for your trailer wiring should be for the running lights while the white wire should be for ground. Typically clearance lights use black for power and white for ground, like part #MCL32AB, but in the case of black and red wiring the…

view full answer...

Answer 2

Two-wire LED clearance lights such as the Red #MCL32RB or the Amber #MCL44AB have one wire for the power lead and one ground wire. The wire that was attached to your old clearance lights will be spliced to the power wire of your new lights. The black…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…

view full answer...

LED Amber Colored Trailer Clearance Light with 2 Wire Design

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching