Mounting Hole Diameter of Brophy D-Ring Tie Down Anchor # LRB1

Question

Question:

LRB1 Brophy D-Ring Tie Down Anchor - Bolt-On - 2-3/8inch Wide - Surface Mount - 4,000 lbs - LRB1. Could you please tell me what the diameters of the bolted down piece for this item? Thank you.

asked by: Colleen N

0

Expert Reply:

Sounds like you are asking about the distance between the mounting holes of the # LRB1, which is 2 inches, or the diameter of ring it is designed to fit which is 1/2 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The inner measurement of the Brophy D-Ring Tie Down Anchor item #DR01 is 2 1/4". I have attached a diagram with the measurement.

view full answer...

Answer 2

The mounting hole dimensions of the Brophy Rope D-Ring Tie-Down Anchor #SS15-C that you referenced is 7/16 inch by 7/16 inch. Best option would be to use a carriage bolt with shoulders that match that dimension and you'd be set.

view full answer...

Answer 3

The distance between the closest part of the mounting holes for the CargoSmart 1/2" Anti-Rattle D-Ring Tie-Down Anchor #3486509 measures right at 1-21/32". I have attached a photo to demonstrate this for you.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Mounting Hole Diameter of Brophy D-Ring Tie Down Anchor # LRB1

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching