What Hitch Will Fit A 2011 Acura RDX

Question

Question:

You show this hitch for a 2010 Acura RDX. Will this hitch also fit the 2011 model? Drawtite shows their Model #75784 will fit either year. Shouldnt this do the same?

asked by: Mike N

0

Expert Reply:

The Curt Class III 2 Inch Hitch, part # C13154, will fit a 2010 and 2011 Acura RDX, as well as a 2012 model.

The Draw-Tite Class III 2 Inch Hitch, part # 75784, will also fit the 2010-2012 Acura RDX.

I am including links to the installation instructions on all four of the hitches.

expert reply by: Jeff D

0

Answer 1

For your 2011 Acura RDX, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #56008 may require an extra fuse to be added, but it does not require a dealer. You can see in the attached video of the 2015 model where that…

view full answer...

Answer 2

I spoke with my contact at Curt and he stated that the Curt T-Connector Vehicle Wiring Harness, #56008, has been tested on a 2010 Acura RDX so you can use it! I have linked a video showing an example installation for you.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

What Hitch Will Fit A 2011 Acura RDX

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching