See what our Experts say about this CURT Trailer Hitch

• Replacement Hardware Kit Needed for 2017 Acura RDX Curt Hitch
  Hey Marc, thanks for reaching out! To get all of the replacement hardware for your Curt Trailer Hitch Receiver # C13130 you'll need our part # RHK. I tried looking up the 13130-BK kit you mentioned and couldn't find it, but what I can say is that our RHK kit will include all of the hardware you need to get the hitch installed. Attached is our installation video as well as a photo showing this hitch installed for your reference.
  view full answer...
• Recommended Bike Rack For Hauling 4 Bikes On A 2014 Acura RDX
  Yes, both the etrailer Trailer Hitch Receiver # e24AR and Curt Trailer Hitch Receiver # C13130 would be a fit for your 2014 Acura RDX. Since you're limited on capacity the Hollywood Racks Destination Bike Rack for 4 Bikes # HR4000 would be a great option to haul 4 bikes. This hitch mounted bike rack weighs approximately 47lbs and can handle up to 35lbs per bike. It has straps at each wheel cradle and padded clamps on towers in the middle of the rack to clamp on to the frame of the bikes...
  view full answer...
• Distance From Ground To Inside Top of Receiver on etrailer Trailer Hitch Receiver For 2017 Acura RDX
  The distance from the ground to the inside top of the receiver for the etrailer Trailer Hitch Receiver # e24AR is 12-1/2". I have attached an image below showing this measurement on the Curt # C13130. The etrailer hitch is identical with the exception of the matte black powder coat finish. Since it sounds like you plan on towing, you will also want wiring. For the most reliable option I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118569. This plugs into...
  view full answer...
  
• Replacement Handle Nut and Matching Bolts for Curt Trailer Hitch C13130
  For a 1/2"-13 handle nut you can use # 1332 which is sold in quantities of 1. I have also included a link to the installation instructions and a video showing an example installation of Curt trailer hitch C13130 for you. The bolts that match the nuts are only available by purchasing the complete replacement hardware kit for the hitch # RHK. On the RHK page enter the hitch number and choose Curt where indicated to receive the proper hardware. This will include all of the hardware including...
  view full answer...
• Trailer Hitch Recommendation for a 2016 Acura RDX
  The 3 hitches you asked about for your 2016 Acura RDX have the following weights when it comes to shipping: etrailer - # e24AR - 27 lbs Curt - # C13130 - 28 lbs Draw-Tite - # 75784 - 29 lbs The actual weight of the hitches is going to be a few pounds less since the shipping weight includes shipping materials. These are all going to have the exact same installation process and since the weight is all comparable it really boils down to preference. For your application I recommend going...
  view full answer...
• Do I Still Need to Use the Stabilizer Straps on my Curt Hitch When Carrying a Bike Rack
  Stabilizer straps are no longer required when using a Curt hitch like the # C13130; this was an older requirement for some Curt hitches when using a bike rack only, but they have since determined that it is not required or recommended any longer. You could also use the Draw- Tite # 75784, which the main difference is that the receiver is about 1-1/2" shorter, so it's not as ideal for bike racks since the clearance from the vehicle will be minimal. I've linked an installation video of the...
  view full answer...
• Compatibility of 1/2 Inch Bolts with Handle Nuts Used to Install Curt # C13130 on 2013 Acura RDX
  I spoke with my contact at Curt Manufacturing, who confirms that the 12M bolt are indeed intended to fit the weldnuts, and the 1/2 inch bolts are a fit for the handle nuts. My contact suggested that you closely examine the threads on the inside of the handle nuts to make sure they're not damaged, same with the bolts. Try threading the bolts into the handle nuts before you put the handle nuts up into the frame to confirm fit, try both nuts with both bolts. When the handle nuts are up inside...
  view full answer...
• Bolts Won't Thread on Curt Hitch of 2017 Acura RDX
  I do have suggestions if the bolts won't thread when installing the Curt Trailer Hitch Receiver # C13130 on your 2017 Acura RDX. What you can do is use a thread tap, a size M12 x 1.25 to fit the same size bolts.
  view full answer...
• Recommended Hitch, Cargo Carrier, and Accessories For 2017 Acura RDX
  Hey Robert! Thanks for being interested in joining the hitch club! First things first, the Curt Class III # C13130 is a great choice for your 2014 Acura RDX (super easy install) and it'll work great with the Curt Cargo Carrier # C18113 you have your eyes on. Fit and compatibility verified. Now for the extras, I definitely do recommend adding an anti-rattle pin and lock, and you can do both with part # 63232. This will secure the carrier to your vehicle and drastically reduce any movement/noise...
  view full answer...
• Does Curt Trailer Hitch For 2018 Acura RDX Require Spacer Blocks & Work With Yakima HoldUp Bike Rack
  Spacers are not needed in order to install the Curt Trailer Hitch Receiver # C13130 on your 2018 Acura RDX and the reason is Curt decided that the hitch would fit fine without them, even though it will push up against the underneath fascia a bit. This is in contrast to the Draw-Tite Trailer Hitch Receiver # 75784, which, like you pointed out, does require spacer blocks in order to ensure the hitch wasn't pushing up against that fascia. Both will work though, and there hasn't been any...
  view full answer...
• Best Trailer Hitch and Bike Rack for 2018 Acura RDX
  The best trailer hitch for your 2018 Acura RDX to carry a bike rack is the Curt # C13130 because it has clean look with a concealed cross tube and the highest tongue weight capacity among the hitches that fit your Acura, which speaks to the strength of the hitch. This Class III, 2" hitch is made in the USA and is a complete bolt-on installation that will not require any type of drilling into your car's frame. I have added a photo showing how the hitch looks when installed on a RDX as well...
  view full answer...
  
• Trailer Hitch Recommendation for 2013 Acura RDX Towing 1750 LB Fishing Boat
  I have included a link to the hitch options that we offer for your 2013 Acura RDX. The hitch that I recommend for your 2013 Acura RDX is the Curt Class III Trailer Hitch Receiver, # C13130. This is a custom fit hitch so there is no drilling or welding required for installation and it has a towing capacity of 4,000 lbs and tongue weight capacity of 600 lbs. Although the hitch has a 4,000 lb capacity, I did some checking and it looks as though your RDX has a maximum towing capacity of 1,500...
  view full answer...
• Replacement Hitch Hardware Kit for Curt Hitch C13130 for 2017 Acura RDX
  The hitch you purchased is Curt # C13130. This hitch fits the Acura RDX for model years 2013 through 2017 so you can re-install it on the newer vehicle. Hitch hardware can be used only one time so to mount this hitch on the 2017 RDX you will need our Replacement Hardware Kit # RHK. Simply enter that item in our search box and then select the Curt brand and part C13130. The hardware kit will include everything needed to mount the hitch on the RDX.
  view full answer...
• Trailer Hitch for 2016 Acura RDX for Use with Thule T2 Platform Rack and Pedego Bikes
  All three of the 2-inch hitches we offer for your 2016 Acura RDX, one of which is the Curt # C13130, will mount to the same points on your RDX. All will be in essentially the same position at the rear of the car, with the hitch pin hole about 3-1/2-inches from the rear edge of the bumper. Of the three hitch options I suggest the Draw-Tite # 75784 since it is the lowest-cost hitch and since it does not require you to use a stabilizing strap which is required for the Curt hitch. Your Thule...
  view full answer...
• Recommended Trailer Hitch for a Bike Rack on a 2016 Acura RDX
  We always recommend using a trailer hitch with a 2" receiver over the 1-1/4" size because they have higher weight ratings and because you can use a wider variety of bike racks. Technically since the 1-1/4" is smaller it will be less noticeable but realistically there isn't that big of a visual difference between the 2 sizes. I recommend using the Curt Class III Trailer Hitch # C13130 for your 2016 Acura RDX which gives you that 2" receiver plus it installs in such a way that only the receiver...
  view full answer...
  
• Recommended 2 Inch Hitch for 2013 Acura RDX
  Yes. I recommend using the Curt # C13130 because of the durability of the powder coating on their hitches. This has a 2" receiver that provides you with a better variety of hitch mounted accessories and is much better suited for towing if the need arises. If you're going to be towing, I've listed the appropriate wiring harness and other parts you'll need to complete your towing setup below. Wiring: # 118569 (Tekonsha has the most reliable converter boxes) Ball Mount/Hitch Ball: # 989900...
  view full answer...
• Trailer Hitch And Hitch Bike Rack To Carry Rad Wagon 4 & Road Bike On 2015 Acura RDX
  Let's start with the trailer hitch for your 2015 Acura RDX. I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2", part # C13130. It has a maximum tongue weight of 600 lbs and a maximum gross trailer weight of 6,000 lbs. We have one hitch bike rack able to carry a bike the weight of your Rad Wagon, the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount, part # HLY84FR. It can carry bikes with wheelbases up to 60" and weigh up to...
  view full answer...
• Stabilizer Strap Recommendation for Curt Hitch C13130 on a 2013 Acura RDX
  The correct stabilizer strap to use with the Curt Hitch part # C13130 that you referenced is the part # 18050. To see how it would get used check out the review video I attached. Another option you have that might interest you is to use a Draw-Tite Hitch like part # 75784. It does not require the use of a stabilizer strap. I attached an install video for this hitch for you to check out as well. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman...
  view full answer...
• Does Curt Trailer Hitch Receiver Fit 2017 Acura RDX
  Yes it does! The Curt Trailer Hitch Receiver # C13130 will absolutely fit your 2017 Acura RDX. In fact, the accompanying photos show this hitch on a '17 RDX. This is a simple, bolt-on installation that doesn't require any drilling or fascia/bumper cutting of any kind; all you have to do is lift the hitch into place and bolt it on. I have added a link to a video install on a 2017 Acura RDX for you to check out as well of the Curt Trailer Hitch Receiver # C13130. If you are looking to...
  view full answer...
  
• Does Curt Trailer Hitch and Wiring Harness Fit 2018 Acura RDX
  I am happy to confirm you are on the money with the Curt trailer hitch receiver and trailer wiring harness that fit your 2018 Acura RDX: - Curt Trailer Hitch Receiver # C13130 - Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 56008 Both of these items will fit your 2018 Acura RDX and will allow you to tow your boat as well as use a bike rack. The Curt Towing Starter Kit for 2" Hitches # C45534 may be the ball mount you need, but it depends on if its 3/4"...
  view full answer...
  
• Recommended Trailer Hitch and 3 Bike Carrier for 2018 Acura RDX
  Let's begin with the hitch. I'd recommend the Curt Class III, part # C13130. This is a concealed crossbar hitch, when installed as shown in the provided photo only the receiver tube and safety chain loops will be visible for a clean look. If the bikes in question don't have fenders, the RockyMounts WestSlope # RKY10223 would be a good choice. The rack can handle 3 bikes weighing up to 40 lbs each, with tires up to 3 inches wide and wheelbases up to 48 inches. The rack also has an available...
  view full answer...
  
• Curt Class lll Trailer Hitch and SportRack 3 Bike carrier for 2013 Acura RDX
  The Curt Trailer Hitch Receiver, part # C13130, is a fit for your Acura RDX. The hitch has a 2 inch by 2 inch receiver opening and has a tongue capacity of 600 lbs. Please note that this hitch has a gross trailer weight maximum of 4000 lbs and and a tongue weight capacity of 600 lbs. This hitch is not designed to be used with a weight distribution system. The SportRack 3 Bike Carrier, part # SR2403 measures 12-1/4 inches from the center of the hitch pin hole to the back of the upright...
  view full answer...
• Is Curt Class III Trailer Hitch a Good Option for Towing a Tear Drop Trailer with a 2016 Acura RDX
  The Curt Trailer Hitch # C13130 is an excellent option for towing a tear drop trailer behind your 2016 Acura RDX! This features a hidden crosstube so it looks very slick, and the 600 lbs tongue/4,000 lbs towing weight capacities are well over the 150 lb tongue/1,500 lbs towing capacities of your RDX (according to your owner's manual). To complete your towing setup you also need wiring and a ball mount kit. When I looked up the online owner's manual it stated that trailer brakes and a brake...
  view full answer...
• What is the Stabilizer Strap that Curt Recommends Get Used with Their Hitches
  A stabilizer strap will attach to the hitch accessory and then attach to the vehicle to provide support for the accessory to help prevent some of the shock from bumps from being transferred to the hitch. The Curt Strap part # 18050 is one that is most often used. I attached a demo video that shows how to use this product for you to check out.
  view full answer...

Do you have a question about this Trailer Hitch?