Which Pigtails Are Needed For The GloLight LED Trailer Light STL201RFMB?

Question

Question:

Hi, need a pair of these for a flatbed. Which pigtails do I need? Both A42PMBB, and A45PMB? Thanks

asked by: Roger

0

Expert Reply:

Yes, the Optronics GloLight LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - 24 Diodes - Weathertight, # STL201RFMB, uses two weathertight harnesses. The 3-Wire Pigtail for Optronics Trailer Lights - Weathertight Plug - 10" Lead, # A45PMB, will give you the running light, stop light, and turn signal funtions. The 2-Wire Pigtail for Optronics Lights - Weathertight Plug - 10" Lead, # A42PMB, will give you the backup light funtion.

To connect these harnesses, I suggest using heat shrink butt connectors like # DW05744-5.

expert reply by: Jason S

0

Answer 1

Yes, the wire colors of the Deka Wire - Jacketed 7-Wire #DK74FR are the industry standards that you mentioned. Black, white, red, green, white, yellow, and blue.

view full answer...

Answer 2

I reached out to my contact at Curt and was able to get a dimension sheet for the Curt Trailer Hitch Receiver - Class V #C15810 referenced in your question. I have attached an image of it for your review. This trailer hitch is designed to fit select…

view full answer...

Answer 3

The drop of the Curt Class V #C15810, which is the distance from the top of the hitch crossbar to the underside of the vehicle frame where the hitch mounting flanges attach to the vehicle is 5.63 inches. The distance from the face of the receiver to…

view full answer...

Answer 4

I spoke with my technical contact at Curt and he informed me that the Curt Hitch #C15810 will fit spare tires with a wheel size of less than 20 inches. We happen to have a Ford F-350 on site, so we checked out the spare tire underneath and it was a…

view full answer...

Answer 5

The width of your frame indicates that your 2012 Ford F-450 is most likely a cab and chassis model which has the frame width a few inches than a standard truck bed. But if you can measure the distance between the mounting holes on the frame of your…

view full answer...

Answer 6

I have another option for you, but there is not a no drill mounting bracket that has a longer clamp than the #C57202 you purchased. Instead I recommend the Curt Easy Mount Bracket #C58003 which will mount to the receiver tube of the Curt Trailer…

view full answer...

Answer 7

To install the GloLight LED Trailer Tail Light #STL201RFMB that you referenced you would need to have a 4.5 inch hole cut in the trailer. The light portion of the assembly is 4.5 inches which would recess into the hole and the flange has an outer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...