Available Trailer Jack Caster Wheels

Question

Question:

Looking for a foot wheel

asked by: Gilberto

0

Expert Reply:

You can see all of our available jack caster wheel assemblies on the linked page. These fit on a 2-inch-diameter jack tube, such as # BD500245. If you can find a brand name or part number on your jack that will help to narrow down the correct parts, but as long as the tubing diameter matches up you should be fine using a different brand of wheel.

We have plastic wheels in various dimensions, such as the 6-inch # JC-101 and also a steel wheel # JC-102.

expert reply by: Adam R

0

Answer 1

The Ram Removable Caster Assembly, #JC-101, is a swiveling caster when attached to the jack. The caster assembly uses a nylon bushing at the swivel point between the connected mounting tube and the wheel assembly.

view full answer...

Answer 2

The 3" bolt hole spacing is the standard pattern for mounting bolt holes on most trailers. The Lippert Quick Drop Tongue Jack #LC733926 that you are looking at will match that same pattern. Do note that the holes on the jack are oblong to…

view full answer...

Answer 3

In either position the handle of the Lippert Quick Drop Tongue Jack #LC733926 would not spin and lower on it's own. There's enough friction in the screw of the jack to prevent vibration from causing it to turn on it's own.

view full answer...

Answer 4

To add a wheel with the Round A-Frame Trailer Jack #TJA-5000S-B all you need is the wheel caster #JC-101. I would recommend supporting the tongue of the trailer with a floor jack before taking apart anything internal of the jack.

view full answer...

Answer 5

I tested a few wheels that we have in stock and found that the #JC-102 would physically fit on the Lippert Quick Drop Tongue Jack #LC733926, but would limit your capacity down to wheel's at 1,200lbs.

view full answer...

Answer 6

The vast majority of trailer jack wheels don't use traditional steel ball bearings as they aren't really meant for rotation speed but rather weight bearings. I am not aware of any options which use traditional steel ball bearings. The…

view full answer...

Answer 7

Hi Roger, I checked with Lippert, and sadly a gear is not an available replacement part for the Lippert Quick Drop Tongue Jack #LC733926. The only replaceable parts are the mounting hardware and footpad so the best I can offer is to replace it with a…

view full answer...

Answer 8

Gary, I find the Ark Xtreme Off-Road Swivel Trailer Jack #ORJW350D is one of the best jacks for using the wheel to move a trailer around. It has a dual wheel setup which also makes it easier on loose surfaces such as gravel and grass. This jack will…

view full answer...

Answer 9

The only 8" caster wheel we have is for a Fulton F2 jack with the Wide-Track Wheel Assembly #F500266. This does have a cross-pattern style attachment though so if you have something other than a Fulton F2 it won't work and you'll need to…

view full answer...

Answer 10

Hey Martin, The Replacement Male Pipe for Curt Pipe Mount Swivel Jacks #C46FV has a 2" outer diameter which is pretty standard for pipe-mounted swivel jacks so it would likely be a fit. I wasn't able to confirm the female side of this on the…

view full answer...

Answer 11

It would be possible to cut off the footplate on jack #TJP-2002S-B but doing so would of course void the item's warranty. Also, the drilling of the two holes needed to install a caster wheel like #JC-101 would possibly weaken that inner jack…

view full answer...

Answer 12

You can replace your trailer's jack foot plate with a trailer caster wheel. Your tongue weight capacity will be the lowest of three numbers, 1.) the new caster wheel capacity, 2.) the old tongue jack capacity, or 3.)the trailers stated TONGUE…

view full answer...

Available Trailer Jack Caster Wheels

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching