Differences Between the Curt Hitches for the 2009 Toyota Matrix

Question

Question:

What is the difference between curt hitch c12221 and c12228 for a 2009 Toyota Matrix s

asked by: Mark A

0

Expert Reply:

The difference is the shape of the cross tube. The part # C12228 has a square shaped tube whereas the part # C12221 has a round shape. Typically the round tubes are less visible than the square ones.

expert reply by: Jameson C

0

Answer 1

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 2

I went out to the warehouse and examined the Curt Hitch #12221 and #C12013. While they are similar, there is a key difference in the designs. From the top of the mounting brackets on each side of the hitch down to the bottom of the receiver, hitch…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Yes, you are correct the differences are that on #C12221 the heat shield modification may be required, and lower fascia may need to be trimmed for hitch installation. On the #C12013 a heat shield modification may be required. It does not need a…

view full answer...

Answer 8

I reached out to my contact at Lippert who said that the 733-0001 number you gave me does look like a Coach Step number but he wasn't able to find anything in their system with it. Is there another number somewhere on the steps that has 6 digits…

view full answer...

Answer 9

I took a look at the owner's manual for a 2012 Toyota Matrix and it said it does not recommend towing with the Matrix that has a 1.8L engine, but the Matrix for a 2.4L can, and has a towing capacity of 1,500 lbs. That does not mean you can't…

view full answer...

Answer 10

The Curt Class I Receiver Hitch #C11399 is a confirmed to fit your 2018 Audi A3 as long as you don't have the e-tron model. This hitch has a towing capacity of 2,000 pounds and a 200 pounds tongue weight. As far as its construction, performance,…

view full answer...

Answer 11

You have two general options for bike racks for use on your 2010 Matrix: a hitch mount rack (that requires a hitch be installed on the vehicle) and a trunk-mount type. The trunk mount route will be more cost-effective, but the hitch-mount option…

view full answer...

Answer 12

The Curt Class-II hitch #C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite #24812 is a Class-I hitch where as the Curt #12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But…

view full answer...

Differences Between the Curt Hitches for the 2009 Toyota Matrix

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching