Which Pucks of a 2016 Ram Rail Kit are Designed for the Safety Chain Loops

Question

Question:

Do you have the safety chain loops for the front holes in the factory install on the 2016 dodge gooseneck as these fit the rear holes only

asked by: Jeff

0

Expert Reply:

The rear pucks of the rail kit in your 2016 Ram are the ones all of the safety chain loops we carry are designed to fit. You would only need two of them so using the part # C60617 in the rear would be just fine. Mopar designed the front pucks slightly different so these would not fit in them.

expert reply by: Jameson C

0

click to enlarge

Answer 1

If you are looking for front puck tie-downs, the best bet is the Curt Safety Chain Loops for Factory Ram Underbed Gooseneck Trailer Hitch #C60617. I confirmed with Curt that these should work with your front pucks as well.

view full answer...

Answer 2

The Safety Chain Loops I recommend for your 2016 Ram 2500 with the factory gooseneck hitch is part #C60617.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Which Pucks of a 2016 Ram Rail Kit are Designed for the Safety Chain Loops

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching