Torque For Brake Assembly Mounting Flange on Trailer

Question

Question:

I JUST BOUGHT 4 NEW AKEBRK-7L AND7R -SA BREAKE ASSEMBLYS. I WOULD LIKE TO TORQUE SPEC.FOR FIVE BOLTS FOR INSTALLING BRAKE ASSEMBLY TO AXLE. THANKS

asked by: JAMES M

0

Expert Reply:

30-50 ft lbs of torque is the recommended torque spec for installing the etrailer.com brake assemblies part # AKEBRK-7L-SA.

If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close to that range.

expert reply by: Jameson C

0

Answer 1

It is possible to use the Replacement Trailer Hub Wheel Stud #RG03-080 which is 1/2" wheel stud, inside your Lippert 6k hub, which uses a 9/16" stud. You'll want make sure that the stud is drive in as opposed to threaded, and,…

view full answer...

Answer 2

Hey Tim, yes the replacement hub/drum part #AKHD-865-7-2-EZ-K is correct for your Lippert 7k axles as well as the replacement brake assembly set part #AKEBRK-7-SA. Here's how to torque the spindle nut: 1. After placing the hub, bearings, washers,…

view full answer...

Answer 3

The studs on the trailer hub and drum assembly #42866UC3-EZ, are 1/2 inch-20. The assembly comes with lug nuts, bearings, grease seal, and a dust cap. The bolt pattern is 8 on 6-1/2. If you needed the same hub and drum assembly but with the 9/16 inch…

view full answer...

Answer 4

Hello Chris, The grease that is used to pre-grease our hubs is a lithium based grease. They come pre-greased from AxleTek. With that being said, if you are looking to add more grease it doesn't need to be brand specific. What we use here in our…

view full answer...

Answer 5

The bolts used to secure the Electric Trailer Brake Kit part #AKEBRK-7-SA to your axle will need to be torqued to 30-50 ft-lbs. If you do not have access to a torque wrench then you can tighten the bolts down enough to where the lock washer is…

view full answer...

Answer 6

For a set of self-adjusting brake assemblies that fit your 5,200 lb axles that have 12 x 2 inch drums you'd want the part #AKEBRK-7-SA and you'd be set.

view full answer...

Answer 7

In regards to the Electric Trailer Brake Kits like part #AKEBRK-7-SA, the most common issue we see with the brakes not engaging after install would be installing the assemblies on the wrong side. This is very easy to check, the actuating arm will be…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Torque For Brake Assembly Mounting Flange on Trailer

Product Page this Question was Asked From

Continue Researching